Bedienungsanleitung Black Decker GK1635T T4 (Seite 12 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

584950

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

◆ If the chain does not come to rest immediately

then this indicates that it needs tensioning

(see „Fitting the guide bar and chain“).

How to switch the tool on (fig. A)

◆ Grip your chainsaw firmly with both hands.

Push the lock-off button (2) forward and then

push the on/off switch (1) to start.

◆ When the motor starts, remove your thumb

from the lock button and grip the handle firmly.

Do not force the tool - allow it to do the work.

It will do a better and safer job at the speed for

which it is designed. Excessive force will stretch

the chain.

If the saw chain or bar becomes jammed:

◆ Switch the tool off.

◆ Disconnect the tool from the mains supply.

◆ Open the cut with wedges to relieve the strain

on the guide bar. Do not try to wrench the saw

free. Start a fresh cut.

Felling (fig. H - J)

◆ Pre-plan a safe exit from falling trees or branches.

◆ Cut one third of the diameter of the tree (Fig. H).

Then cut down from above to make a notch of

about 45°. This way you will avoid pinching the

saw.

◆ Make a single felling cut from the other side

but stop before you cut through to the notch

(fig. I).

◆ Drive a wedge or wedges into the felling cut to

open it and drop the tree (fig. J).

Logging (fig. K - M)

How you should cut depends on how the log is

supported. Use a saw horse whenever possible.

Always start a cut with the chain running and the

spiked bumper (17) in contact with the wood (fig. K).

To complete the cut use a pivoting action of the

spiked bumper against the wood.

When supported along its whole length

◆ Make a downward cut, but avoid cutting the

earth as this will blunt your saw quickly.

When supported at both ends

◆ First, cut one third down to avoid splintering

and second, cut again to meet the first cut.

When supported at one end

◆ First, cut one third up to avoid splintering and

second, cut down to prevent splintering.

When on a slope (fig. L)

◆ Always stand on the uphill side.

When using a saw horse (fig. M)

This is strongly recommended whenever possible.

◆ Position the log in a stable position. Always cut

on the outside of the saw horse arms.

MAINTENANCE (fig. N)

Regular maintenance ensures a long effective life

for the tool. We recommend you make the

following checks on a regular basis.

TROUBLESHOOTING

If the tool does not operate correctly, check the following.

Fault Possible cause Action

Tool will not start. Blown fuse. Replace fuse.

Tripped RCD. Check RCD.

Mains lead not connected. Check mains supply.

Tool will not start

button will not slide. Front guard in the brake position Reset front guard.

Chain does not stop instantly

when the tool is switched off. Chain tension is too slack. Check chain tension.

Bar/chain appear hot/smoking. Oil tank empty. Check oil tank level.

Chain tension is too tight. Check chain tension.

Guide bar sprocket nose needs greasing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GK1635T T4 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info