Bedienungsanleitung Black Decker GK1830 (Seite 7 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

474490

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

(Original instructions)

u Only use replacement guide bars and chains

specified by the manufacturer. Incorrect replacement

guide bars and chains may cause chain breakage and/

or kickback.

u Follow the manufacturer's sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

u Striking metal, cement or any other hard material near

the wood, or buried in the wood can cause kickback.

u A dull or loose chain can cause kickback.

u Do not try to insert into a previous cut. As this could

cause kickback. Make a fresh cut every time.

Safety recommendations for the chainsaw

u We strongly recommend that first time users obtain

practical instruction in the use of the chainsaw and

protective equipment from an experienced user. Initial

practice should be completed sawing logs on a saw

horse or cradle.

u Always check that the kickback brake operates correctly

before use.

u We recommend that when carrying the chainsaw that

you make sure that the brake is engaged and the saw

chain is facing backwards.

u Maintain your chainsaw when not in use. Do not store

your chainsaw for any length of time without first

removing the saw chain and guide bar which should be

kept immersed in oil. Store all parts of your chainsaw in

a dry, secure place out of reach of children.

u We recommend you drain the oil reservoir prior to

storage.

u Be sure of your footing and pre-plan a safe exit from a

falling tree or branches.

u Use wedges to help control felling and prevent binding

the guide bar and saw chain in the cut.

u Saw chain care. Keep the saw chain sharp and snug on

the guide bar. Ensure the saw chain and guide bar are

clean and well oiled. Keep handles dry, clean and free

from oil and grease.

Avoid cutting

u Prepared timber.

u Into the ground.

u Into wire fences, nails. etc.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). The extension

cable must be suitable for outdoor use and marked

accordingly. Up to 30 m of HO7RN-F 2 X 1.5 mm²

extension cable can be used without loss of product

performance. Before use, inspect the extension cable for

signs of damage, wear and ageing. Replace the extension

cable if damaged or defective. When using a cable reel,

always unwind the cable completely.

Voltage drops

u Under certain power supply conditions this product may

cause short-time voltage drops during start-up.

u Other equipment may be affected. For example, electric

lights may temporarily reduce in brightness.

u Contact the supply authority, if necessary, to determine

that the impedance of the power supply is lower than

0.411 ohms. Disturbances are unlikely to occur under this

condition.

Guard against electric shock

u Prevent body contact with earthed or grounded surfaces

(e.g. metal railings, lamp-posts etc.). Electric safety can be

further improved by using a high-sensitivity (30 mA/

30mS) Residual Current Device (RCD).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GK1830 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info