Bedienungsanleitung Black Decker GK1935 T3 (Seite 9 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

584963

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

(Original instructions)

Oiling the chain

You must do this whenever you use a new chain (6) for the

rst time. Take the new chain (6) and soak it in chain oil for at

least an hour before using it. Use Black & Decker chain oil.

We recommend that you use only Black & Decker oil during

the lifetime of your chainsaw because mixtures of different oils

could lead to the oil becoming degraded, which can drastically

shorten the lifetime of the saw chain and create additional

risks.

Never use waste oil, thick oil or very thin sewing machine oil.

These may damage your chainsaw.

Fitting the guide bar and chain. (g. A - E)

u Place the chainsaw onto a stable surface.

u Set the front guard/chain brake assembly to the forward

position (fig. D).

u Fully loosen the chain adjust locking knob (9) (fig. A).

u Remove the chain cover assembly (10).

u Place the chain (6) over the guide bar (7) making sure that

the saw chain cutters on the upper part of the guide bar

(7) face towards the front (fig. B2).

u Guide the chain (6) around the guide bar (7) and pull it to

create a loop to one side at the rear end of the guide bar

(7).

u Guide the chain (6) around the drive sprocket (12). Place

the guide bar (7) onto the bar location studs (13) (fig. B1).

Make sure that the sliding nut peg (14) locates into the

tensioning hole (15) (fig. E).

Warning! Make sure that the front guard/chain brake

assembly (4) is in the set (forward) position before retting

(g. C).

u Place the chain cover assembly (10) onto the chainsaw.

u Turn the chain adjust locking knob (9) to attach the chain

cover assembly (10) but do not tighten fully.

u Turn the chain tension adjust screw (5) clockwise until the

chain (6) is tight. Make sure that the chain (6) is snug

around the guide bar (7).

u Check the tension as described below. Do not overtighten.

u Tighten the chain adjust locking knob (9).

Checking and adjusting the chain tension

(g. G)

Before use and after every 10 minutes of use, you must

check the chain tension.

u Disconnect the tool from the mains supply.

u Lightly pull on the chain (6) as shown (inset fig. G). The

tension is correct when the chain (6) snaps back after

being pulled 3 mm away from the guide bar (7). There

should be no "sag" between the guide bar (7) and the

chain (6) on the underside.

Note: Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the guide bar and

the chain.

Note: When the chain is new, check the tension frequently

(after disconnecting from the mains) during the rst 2 hours

of use because a new chain stretches slightly.

To increase the tension

u Turn the chain adjust locking knob (9) counterclockwise.

u Tension the chain using the chain tension adjusting screw

(5), turn clockwise to tighten.

u Tighten the chain adjust locking knob (9).

Use

Warning! Let the tool work at its own pace. Do not overload.

Filling the oil reservoir (g. F)

u Remove the oil cap (3) and fill the reservoir with the

recommended chain oil. You can see the oil level in the oil

level indicator (11). Refit the oil cap (3).

u Periodically switch off and check the oil level indicator

(11); if it is less than a quarter full, disconnect your

chainsaw from the mains supply and refill with the correct

oil.

Switching on

Note: It will not be possible to switch the tool on if the

front guard/chain brake assembly is not in the "set"

position.

u Grip your chainsaw firmly with both hands. Push the

lock-off button (2) and then push the on/off switch (1) to

start.

u When the motor starts, remove your thumb from the lock

button (2) and grip the handle firmly.

Do not force the tool, allow the tool to do the work.

It will do a better and safer job at the speed for which it is

designed. Excessive force will stretch the saw chain (6).

How to set the chain brake (g. C)

u Make sure that the tool is disconnected from the mains

supply.

u Pull the front guard/chain brake assembly (4) back into the

"set" (fig. C) position.

u The tool is now ready to use.

How the anti-kickback chain brake works

In the event of kickback, your left hand comes in contact with

the front guard, pushing it forwards, toward the workpiece,

and stops the tool within a few fractions of a second.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GK1935 T3 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info