Bedienungsanleitung Black Decker GKC108 TH1 (Seite 7 von 12) (Englisch)

585839

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

u Once the cut is complete, the clamping arm will rotate fully

back to the stop position.

Sawing (g. E)

u Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u If possible, work with the shoe (6) pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being dam-

aged.

Hints for optimum use

Cutting branches

Branches up to 75 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or

on any other unstable surface. Be aware of where the branch

will fall.

u Make sure the tool is running at full speed before making

a cut.

u Hold the tool rmly in place to avoid possible bouncing or

sideways movement of the tool.

u Guide the tool using light pressure.

u Always cut down from the top. This way you will avoid

pinching the saw blade.

u Remove branches starting from branch tip. Reduce the

branch in logical steps cutting off small sections.

u When cutting a limb that is under tension be aware of

spring back. When the tension in the wood bers are

released the spring loaded limb may strike the operator

and /or throw the tool out of control.

u Remove the tool from the cut while it is running at full

speed.

Cutting metal

u Use a ner blade (24 teeth per inch) for ferrous metals

and a coarse blade for non-ferrous materials.

u In thin gauge sheet metals it is best to clamp wood to the

underside of the sheet. This will ensure a clean cut without

excess vibration or tearing of metal.

u Avoid forcing cutting blade as this reduces blade life and

causes costly blade breakage.

Note! Spread a thin lm of oil or other coolant along the line

ahead of the saw cut for easier operation and longer blade

life. Aluminum should be cut dry.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the perform-

ance of your tool. By using these accessories you will get the

very best from your tool.

Blades

The saw will accept a blade up to 15 cm long. Always use the

shortest blade suitable for your project but long enough to

keep the blade cutting through the material. Longer blades are

more likely to be bent or damaged during use. During opera-

tion some longer blades may vibrate or shake if the saw is not

kept in contact with the workpiece.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance. Continu-

ous satisfactory operation depends upon proper tool care and

regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

Separate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GKC108 TH1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GKC108 TH1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info