Bedienungsanleitung Black Decker GKC1820L20 (Seite 10 von 16) (Englisch)

585831

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Assembly

Warning! Before assembly, remove the battery (10) from the

tool.

Fitting and removing the battery (fig. A)



To fit the battery (10), line it up with the receptacle on

the tool. Slide the battery (10) into the receptacle and

push until the battery (10) snaps into place.

 To remove the battery (10), push the release button (24)

while at the same time pulling the battery (10) out of the

receptacle.

Warning! To prevent accidental operation, make sure that

the battery is removed and that the chain sheath (11) is in

place on the

saw chain (8) before performing the following

operations. Failure to do this could result in serious personal

injury.

Installing and removing the saw chain (fig. C, E & G)

 Place the tool on a firm and stable surface.

 Loosen the two Allen screws (14) using the Allen key

(21) provided. Remove the Allen screws (14).

 Remove the chain cover assembly (6).

 Turn the chain tension adjustment screw (7) counter

clockwise to allow the guide bar (9) to recede and to

reduce the tension on the saw chain (8).



Remove the old saw chain (8) from the sprocket (15)

and the guide bar (9).

 Place the new saw chain (8) in the groove of the guide

bar (9) and around the sprocket (15). Make sure that the

teeth are facing the correct direction by matching the

arrow on the saw chain (8) with the arrow on the chain

cover assembly (6).



Make sure that the slot (17) in the guide bar (9) is over

the location pins (18) and that the hole (20) below the

slot is located over the adjustment pin (19).

 Fit the chain cover assembly (6) and the 2 Allen screws

(14).

 Tighten the Allen screws (14) using the Allen key (21)

provided.

Always wear protective gloves when installing or

removing the saw chain (8). The saw chain is

sharp and can cut you when it is not running.

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

 To charge the battery (10), insert it into the charger (12).

force. Be sure that the battery is fully seated in the

charger.

 Plug in the charger and switch on at the mains.

The charging indicator (23) will blink.

The charge is complete when the charging indicator (23)

switches to continuously on. The charger and the battery can

charger occasionally tops up the battery charge.

 Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

pack fresh and fully charged.

 Adjust the chain tension as described below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GKC1820L20 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GKC1820L20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info