Bedienungsanleitung Black Decker GL225 (Seite 10 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527568

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

◆ Loop the cable through the cable restraint (9)

as shown to prevent the extension cable from

becoming detached during use.

◆ Insert the mains plug into a mains outlet.

The extension cable must be suitable for

outdoor use.

USE

Let the tool work at its own pace.

Do not overload.

Switching on and off (fig. A)

◆ To switch the tool on, push the on/off switch (1).

◆ To switch the tool off, release the the

on/off switch.

Never attempt to lock a switch in the on

position.

Hints for optimum use

◆ Hold the tool as shown in fig. G.

◆ Gently swing the trimmer from side to side as

shown in fig. G.

◆ When cutting long grass, work in stages from

the top.

◆ Keep the tool away from hard objects and

delicate plants.

◆ If the tool starts running slowly, reduce the load.

◆ In order to achieve optimum cutting results,

only cut dry grass.

◆ Replace the cutting line when worn.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

◆ Before performing any maintenance,

switch off and unplug the tool.

◆ Do not use any abrasive or solvent-

based cleaner.

◆ Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

◆ Regularly clean the cutting line and spool

using a soft brush or dry cloth.

◆ Regularly use a blunt scraper to remove grass

and dirt from the underneath of the guard.

◆ Regularly check the cutting line for wear.

Fitting a new spool of cutting line (fig. D)

Replacement spools of cutting line are available

from your Black & Decker dealer (cat. no. A6044).

◆ Remove the empty spool by pushing it down

(A) and turning counterclockwise (C).

◆ Assemble and fit the new spool as described

above.

Winding new line onto an empty spool (fig. D & F)

You may wind new cutting line onto an empty

spool. Replacement packs of cutting line are

available from your Black & Decker dealer

(cat. no. A6170 (25 m), A6171 (40 m)).

◆ Remove the empty spool from the tool as

described above.

◆ Remove any old cutting line from the spool.

◆ Locate one end of the cutting line in one of the

grooves (16) in the spool as shown.

◆ Wind the cutting line onto the spool in the

direction of the arrow. Make sure to wind the

line on neatly and in layers. Do not criss-cross.

◆ When the spool is full, clip it into the groove (12)

and cut the line. Let the line protrude at least

5 cm from the spool.

◆ Proceed as described above to fit the spool on

the tool.

Only use 1.5 mm diameter Black & Decker

cutting line.

TROUBLESHOOTING

If your tool seems not to operate properly, follow

the instructions below. If this does not solve the

problem, please contact your local Black & Decker

repair agent.

Before proceeding, unplug the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL225 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info