527588
9
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
9
ENGLISH
If the tool starts running slowly, reduce the load.
In order to achieve optimum cutting results,
only cut dry grass.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Before performing any maintenance,
switch off and unplug the tool.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the cutting line and spool
using a soft brush or dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
Do not use any abrasive or solvent-based
cleaner.
Fitting a new spool of cutting line (fig. D)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6481).
Unplug the tool.
Keep the tabs (11) depressed and remove the
spool cover (12) from the housing (7).
Remove the empty spool (13) from the housing.
Remove any dirt and grass from the housing.
Take the new spool and unwind approx.
9 cm of cutting line.
Feed the cutting line through the eyelet (14).
Push the spool onto the drive shaft (15) and
rotate it slightly until it is seated. Make sure
that the cutting line is not trapped under the
spool and that 9 cm of cutting line protrudes
from the housing.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade (6), cut it off so that it just
reaches the blade.
Winding new line onto an empty spool (fig. E)
You may wind new cutting line onto an empty
spool. Replacement packs of cutting line are
available from your Black & Decker dealer
(cat. no. A6170 (25 m), A6171 (40 m)).
Remove the empty spool from the tool as
described above.
Remove any old cutting line from the spool.
Feed 2 cm of cutting line into one of the holes
(16) in the spool as shown.
Bend the cutting line and anchor it in the
L-shaped slot (17).
Wind the cutting line onto the spool in the
direction of the arrow (18). Make sure to wind
the line on neatly and in layers.
Do not criss-cross.
When the wound cutting line reaches the
recesses (19), cut the line. Let the line protrude
approx. 9 cm from the spool and hold a finger
on the line to keep it in place.
Proceed as described above to fit the spool on
the tool.
Only use round 1.5 mm diameter
Black & Decker cutting line. Do not use
Reflex Plus twisted cutting line. The use of
an incorrect type of cutting line can damage
the auto feed mechanism and will void the
warranty.
TROUBLESHOOTING
If your tool seems not to operate properly,
follow the instructions below. If this does not solve
the problem, please contact your local
Black & Decker repair agent.
Before proceeding, unplug the tool.
Tool does not start
Check that the power cables are properly
connected.
Check the mains fuses.
Tool vibrates strongly
Carefully clean the spool housing.
If this does not solve the problem, unwind the
line from the spool and rewind it more tightly.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Black Decker GL30 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info