Bedienungsanleitung Black Decker GL423 (Seite 9 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

527585

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

◆ If the tool starts running slowly, reduce the load.

◆ In order to achieve optimum cutting results,

only cut dry grass.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Before performing any maintenance,

switch off and unplug the tool.

◆ Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

◆ Regularly clean the cutting line and spool

using a soft brush or dry cloth.

◆ Regularly use a blunt scraper to remove grass

and dirt from the underneath of the guard.

Do not use any abrasive or solvent-based

cleaner.

Fitting a new spool of cutting line (fig. D)

Replacement spools of cutting line are available

from your Black & Decker dealer (cat. no. A6481).

◆ Unplug the tool.

◆ Keep the tabs (11) depressed and remove the

spool cover (12) from the housing (7).

◆ Remove the empty spool (13) from the housing.

◆ Remove any dirt and grass from the housing.

◆ Take the new spool and unwind approx.

9 cm of cutting line.

◆ Feed the cutting line through the eyelet (14).

◆ Push the spool onto the drive shaft (15) and

rotate it slightly until it is seated. Make sure

that the cutting line is not trapped under the

spool and that 9 cm of cutting line protrudes

from the housing.

◆ Align the tabs on the spool cover with the

holes in the housing.

◆ Push the cover onto the housing until it snaps

securely into place.

If the cutting line protrudes beyond the

trimming blade (6), cut it off so that it just

reaches the blade.

Winding new line onto an empty spool (fig. E)

You may wind new cutting line onto an empty

spool. Replacement packs of cutting line are

available from your Black & Decker dealer

(cat. no. A6170 (25 m), A6171 (40 m)).

◆ Remove the empty spool from the tool as

described above.

◆ Remove any old cutting line from the spool.

◆ Feed 2 cm of cutting line into one of the holes

(16) in the spool as shown.

◆ Bend the cutting line and anchor it in the

L-shaped slot (17).

◆ Wind the cutting line onto the spool in the

direction of the arrow (18). Make sure to wind

the line on neatly and in layers.

Do not criss-cross.

◆ When the wound cutting line reaches the

recesses (19), cut the line. Let the line protrude

approx. 9 cm from the spool and hold a finger

on the line to keep it in place.

◆ Proceed as described above to fit the spool on

the tool.

Only use round 1.5 mm diameter

Black & Decker cutting line. Do not use

Reflex Plus twisted cutting line. The use of

an incorrect type of cutting line can damage

the auto feed mechanism and will void the

warranty.

TROUBLESHOOTING

If your tool seems not to operate properly,

follow the instructions below. If this does not solve

the problem, please contact your local

Black & Decker repair agent.

Before proceeding, unplug the tool.

Tool does not start

◆ Check that the power cables are properly

connected.

◆ Check the mains fuses.

Tool vibrates strongly

◆ Carefully clean the spool housing.

◆ If this does not solve the problem, unwind the

line from the spool and rewind it more tightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL423 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info