Bedienungsanleitung Black Decker GL560PXC T5 (Seite 6 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

583265

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

• Bend the cutting line over, pulling it

through the adjacent ‘L’ shaped slot.

The cutting line should now be firmly

anchored to the spool and you may

proceed to wind it on in the direction of

the arrows (16).

• Take time to wind the cutting line on

neatly, in layers. Do not criss cross.

• When you have wound on sufficient

cutting line, temporarily park it in one of

the ‘L’ shaped slots to prevent the

spool unravelling, ensuring you leave a

minimum of 9cm (3.5") protruding.

• Fit the spool and spool cover (8) to the

spool housing as described for fitting a

new spool.

Care and maintenance

• For best performance, please keep the cutting

line, spool and air slots in the trimmer body

clean. Use a dry brush or cloth to remove grass,

sap or other dirt.

• Plastic parts may be cleaned by using a mild

soap and a cloth dampened with hot water.

Do not use any type of detergent, cleaner or

solvent which might contain chemicals which

could seriously damage the plastic. Do not spray

your trimmer with water.

• Self lubricating bearings are used in your trimmer,

therefore, lubrication is not required.

Fault finding

Before checking your trimmer for any faults,

disconnect it from the mains.

• If the trimmer will not start, check that all power

cords are properly connected. If this does not

work, check your power point, finally (UK only)

check the fuse and wiring on the extension

cord plug.

• If the automatic line feed fails to operate, it

could be for one of the following reasons:

Line too short or line jammed on spool

• Disconnect your trimmer from the

power supply.

• Remove the spool cover (8) by pushing both

tabs (13) inwards and upwards (Fig. 4).

• Lift the spool (17) approximately 6mm (

/4")

from the spool housing (12), while pulling the

cutting line (5). This will allow you to lengthen

the line while clearing any line jammed inside

the spool. Ensure there is a minimum of 9cm

(3.5") protruding from the spool housing.

• Rotate the spool as necessary to fully seat

the spool and replace the cover by aligning

both tabs on the cover with the slots in the

spool housing and push into place. Ensure

that both tabs are securely located.

Line still jammed on spool

• Disconnect the power supply and remove

the cover, as previously described.

• Lift out the spool (17) completely, holding the

coiled cutting line in place to prevent it

unravelling from the spool (Fig. 7).

• Carefully unwind the cutting line (5) from the

spool until any crossed or trapped loops are

cleared. Rewind the cutting line evenly, in the

direction of the arrows (16) on the spool.

• Temporarily park the cutting line end in one

of the ‘L’ shaped slots to prevent the spool

unravelling. Ensure you leave a minimum of

9cm (3.5") protruding.

• Turn the lever (14) backwards and forwards

to ensure it operates freely.

• Remove any dirt or grass that may have

collected inside the spool housing and cover.

• Feed the end of the line through the eyelet

and then push the spool into the centre drive

shaft while pulling the free end of the line to

release it from the ‘L’ shaped slot. To fully

seat the spool, rotate as necessary, taking

care not to trap the line underneath the

spool, and making sure that there is a

minimum of 9cm (3.5") of line protruding from

the spool housing.

• Finally, replace the cover as previously

described.

Protecting the environment

Black & Decker provides a facility for

recycling Black & Decker products once

they have reached the end of their working

life. This service is provided free of charge.

To take advantage of this service please

return your product to any authorised repair

agent who will collect them on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

Black & Decker office at the address indicated in

this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our

after-sales service and contacts are available on the

Internet at: www.2helpU.com.

Guarantee

Black & Decker is confident of the quality of its

products and offers an outstanding guarantee.

This guarantee statement is in addition to and in no

way prejudices your statutory rights. The guarantee

is valid within the territories of the Member States

of the European Union and the European Free

Trade Area.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL560PXC T5 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GL560PXC T5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info