Bedienungsanleitung Black Decker GL570C T1 (Seite 5 von 10) (Englisch)

583266

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

N•To gain access under benches, garden

furniture and shrubs (Fig. N).

To alter the cutting head angle:

•With the guard (6) resting on the ground,

depress the pedal (26) with your foot.

•Raise/lower the switch handle (20) while

keeping the pedal depressed. The

cutting head will automatically lock when

you remove your foot from the pedal.

Replacement line

A new spool containing 10 metres of cutting line

(cat. no. A6481) may be purchased from your

Black & Decker dealer. Alternatively, replacement

line packs are available.

For maximum reliability, never put on a heavier or

lighter line (e.g. fishing line) which will prevent the

automatic feed from functioning, cause motor failure

or reduce cutting performance.

How to fit a new spool of cutting line

(Fig. 4 & 5)

•Disconnect your trimmer from the

power supply.

4•Remove the spool cover by pushing the

spool cover tabs (13) inwards and

upwards (Fig. 4), then pull off (it is not

necessary to push both tabs in at the

same time). The empty spool can now

be withdrawn from the drive shaft.

•Remove any dirt or grass that may have

collected inside the spool housing (12)

and cover (8).

5•Unwind approximately 9cm (3.5") of cutting

line (5) from the new spool (17). Feed the

cutting line through the eyelet and then

push the spool onto the centre drive shaft

(Fig. 5). Rotate as necessary to fully seat

the spool, taking care not to trap the cutting

line underneath the spool and making

sure that there is a minimum of 9cm

(3.5") protruding from the spool housing.

•Replace the spool cover by aligning both

tabs on it (13) with the slots in the spool

housing and pushing them into place.

Make sure that both tabs are

securely located.

How to wind new line onto an empty

spool (Fig. 6 & 7)

6•A maximum of 10 metres of new cutting

line can be wound onto the empty spool.

The spool has an ‘Indicator’ to help you

avoid winding an excessive quantity of

cutting line on the spool, as too much will

prevent the automatic feed system from

functioning (Fig. 6).

•Remove any remnant of old cutting line

from the spool (17).

•Push the end of the new cutting line into

one of the two holes provided in the

spool housing (17) and insert 20mm.

•Bend the cutting line over, pulling it

through the adjacent ‘L’ shaped slot.

The cutting line should now be firmly

anchored to the spool and you may

proceed to wind it on in the direction of

the arrows (16).

•Take time to wind the cutting line on

neatly, in layers. Do not criss cross.

•When you have wound on sufficient

cutting line, temporarily park it in one of

the ‘L’ shaped slots to prevent the spool

unravelling, ensuring you leave a

minimum of 9cm (3.5") protruding.

•Fit the spool and spool cover (8) to the

spool housing as described for fitting a

new spool.

Care and maintenance

•For best performance, please keep the cutting

line, spool and air slots in the trimmer body

clean. Use a dry brush or cloth to remove grass,

sap or other dirt.

•Plastic parts may be cleaned by using a mild

soap and a cloth dampened with hot water.

Do not use any type of detergent, cleaner or

solvent which might contain chemicals which

could seriously damage the plastic. Do not spray

your trimmer with water.

•Self lubricating bearings are used in your trimmer,

therefore, lubrication is not required.

Fault finding

Before checking your trimmer for any faults,

disconnect it from the mains.

•If the trimmer will not start, check that all power

cords are properly connected. If this does not

work, check your power point, finally (UK only)

check the fuse and wiring on the extension

cord plug.

•If the automatic line feed fails to operate, it could

be for one of the following reasons:

Line too short or line jammed on spool

•Disconnect your trimmer from the

power supply.

•Remove the spool cover (8) by pushing both

tabs (13) inwards and upwards (Fig. 4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL570C T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GL570C T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info