Bedienungsanleitung Black Decker GL7033 (Seite 8 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527619

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

u When the head is in position, close the height adjust lock-

ing clamp (16).

Note: The tube will only rotate in one direction.

Note: The HDL spool may be used in trimming mode.

Edging mode (g. J)

For edging, the trimmer head should be in the position shown

in g. J. If it is not:

u Release the height adjust locking clamp (16).

u Rotate the tube (7) anti-clockwise.

u When the head is in position, close the height adjust lock-

ing clamp (16).

Note: The tube will only rotate in one direction.

Switching on and off

u To switch the tool on, squeeze the on/off switch (1).

u To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on

position.

Hints for optimum use

General

u In order to achieve optimum cutting results, only cut dry

grass.

Trimming

u Hold the tool as shown in g. K.

u Gently swing the trimmer from side to side.

u When cutting long grass, work in stages from the top. Take

small cuts.

u Keep the tool away from hard objects and delicate plants.

u Cutting line will wear faster and require more feeding if

the cutting is done along pavements or other abrasive

surfaces or heavier weeds are being cut.

u If the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than

50 mm.

u Do not use the tool to create edges. To create edges, use

an edging spade.

u Guide the tool on its wheel as shown in g. L.

u To make a closer cut, slightly tilt the tool.

Fitting a new spool of cutting line (g. M & N)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6482). Packs containing 3

spools of cutting line are also available (cat. no. A6486).

u Unplug the tool.

u Keep the tabs (17) depressed and remove the spool cover

(21) from the housing (12) (g. M).

u Remove the empty spool (22) from the spool cover.

u Remove any dirt and grass from the spool cover and

housing.

u Unclip the end of of the cutting line and guide the line into

the eyelet (23) (g. M). The line should protrude approx.

11 cm from the spool cover.

Note: Take care not to allow the the line on the spool to

unravel. Hold it rmly with one hand at all times..

u Take the new spool and push it onto the boss in the spool

cover. Rotate the spool slightly until it is seated.

u Align the tabs (17) on the spool cover with the cut outs

(24) in the housing (12).

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (11), cut it off so that it just reaches the blade.

Fitting a new piece of heavy duty cutting line (g.

O & P)

Replacement packs of 10 heavy duty cutting lines are avail-

able from your Black & Decker dealer (cat. no. A6489). To t a

new piece of cutting line, proceed as follows:.

u Unplug the tool.

u Keep the tabs (17) depressed and remove the HDL cap

(9) from the housing (12).

u Remove any dirt and grass from the HDL cap (9) and

housing.

u Remove the used piece of line from the HDL cap (9).

u Thread a new piece of line (26) through the eyelets (27) in

either side of the HDL cap.

u Put the central ferrule (28) in the indicated position (Fig.

P).

u Re-t the HDL cap.

Warning! Only use the appropriate type of Black & Decker

cutting line.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL7033 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info