Bedienungsanleitung Black Decker GLC3630L20 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709490

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Chargers

u Use your BLACK+DECKER charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Handle

3. Lock off button

4. Battery

5. Second handle

6. Guard

7. Spool housing

8. Head

9. Edge guide

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the battery has been removed.

Fitting the guard (g. A & B)

u Remove the screw from the guard.

u Keeping the guard (6) square to the strimmer head (8)

slide it into place until the retaining tab clicks into place

(Ensure that the guide rails (10) on the guard (6) are

correctly aligned with the guide rails (11) on the strimmer

head (8).

u Secure the guard (6) with the screw (12).

Warning! Never use the tool unless the guard is properly

tted.

Attaching the second handle (g. C & D )

u Position the second handle (5) over the the tube (13)

u Slide the bolt (14) through the holes in the second handle.

u Tighten the knob (15) onto the bolt by turning it clockwise.

Adjusting the position of the secondary handle (g.

C & D)

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Loosen the knob (15) on the bolt by turning it anti-

clockwise.

u Gently slide the second handle (5) up or down the tube

(13) to the desired height.

u Tighten the knob (15) onto the bolt by turning it clockwise.

Adjusting the height of the tool (g. E)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Release the height adjust locking clamp (16).

u Gently pull the tube (17) up or down to the desired height.

u Close the height adjust locking clamp (16).

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, remove the battery from the tool.

u Remove the tape holding the cutting line to the spool

housing (7).

Fitting and removing the battery (g. F)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (18) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GLC3630L20 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info