Bedienungsanleitung Black Decker GPC1800 TH1 (Seite 9 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

585843

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

• To charge the battery (11), remove it from the

tool and insert it into the charger (12). The

battery will only t into the charger in one way.

Do not force. Be sure that the battery is fully

seated in the charger.

• Plug in the charger.

8 hour charger

The battery will be fully charged in approx. 8 hours.

It can be removed at any time or left in the con-

nected charger indenitely.

Switching on and off (g. E)

For your safety, this tool is equipped with a double

switching system. This system prevents starting

the tool inadvertently.

Switching on

• Push the lock-off button (2) backward using

your thumb and at the same time squeeze the

on/off switch (1).

• Release the lock-off button (2).

Switching off

• Release the on/off switch (1).

Warning! Never attempt to lock a switch in the

on position.

Pruning (g. F)

• Make sure the tool is running at full speed

before making a cut.

• Hold the tool rmly in place to avoid possible

bouncing or sideways movement of the tool.

• Guide the tool through the branch using light

pressure. When cutting heavy branches, where

a partial cut may splinter and damage the tree,

proceed as follows:

-Make the rst cut 15 cm from the tree trunk on

the underside of the limb. Use the top of the

guide bar (7) to make this cut.

-Cut one third through the diameter of the limb.

Then cut down from the top.

Cleaning, maintenance and storage

Your Black & Decker corded/cordless appliance/

tool has been designed to operate over a long

period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon

proper tool care and regular cleaning.

Warning! Before performing any maintencance

on corded/cordless power tools:

• Switch off and unplug the appliance/tool

• Or switch off and remove the battery from

the appliance/tool if the appliance/tool has a

separate battery pack

• Or run the battery down completely if it is

integral and then switch off

• Unplug the charger before cleaning it. Your

charger does not require any maintenance

apart from regular cleaning.

Regularly clean the ventilation slots in you appli-

ance/tool/charger using a soft brush or dry cloth.

Regularly clean the motor houseing using a damp

cloth. Do not use any abrasive or solvent-based

cleaner.

Regularly open the chuck and tap it to remove any

dust from the interior (when tted).

After use and before storage

• Regularly clean the ventilation slots with a

clean, dry paint brush.

• To clean the tool, use only mild soap and a

damp cloth. Never let any liquid get inside the

tool and never immerse any part of the tool into

liquid.

• Remove debris using a hard brush.

• Lubricate the chain with oil.

Installing and removing the saw chain

(g. G & H)

Warning! Always wear protective gloves when

installing or removing the saw chain. The saw

chain is sharp and can cut you when it is not

running.

• Place the tool on a rm and stable surface.

• Loosen the screws (16) using the Allen key

provided. Remove the screws.

• Remove the sprocket cover (5) and the bar

clamp (17).

• Turn the screw (18) counterclockwise to allow

the guide bar (6) to recede and to reduce the

tension on the saw chain (7).

• Remove the old saw chain from the sprocket

(19) and the guide bar (6).

• Place the new saw chain in the groove of the

guide bar and around the sprocket. Make sure

that the teeth are facing the correct direction by

matching the arrow on the saw chain with the

arrow on the housing.

• Make sure that the slot (20) in the guide bar

is over the location pins (21) and that the hole

(22) below the slot is located over the adjust-

ment pin (23).

• Re-t the sprocket cover (5) and the bar clamp

(17) and the screws (16).

ENGLISH

(Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GPC1800 TH1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GPC1800 TH1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info