Bedienungsanleitung Black Decker GR350 (Seite 4 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

474467

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

The handle (9) comprises the lower handle

(10), upper handle (11), switch box (24),

switch lever (21) and safety lock-off button

(20), electrical supply cable (19), cable clips

(12,13) and the handle clamp assemblies,

which comprise a wing nut (15), washer (16)

and bolt (17).

Assemble the lower handle (10) into correct

locations on your mower body, as follows:

• The lower handle (10) comes ready

assembled to your mower body (1) by

means of a pivot pin (8), wing nuts (15),

and washers (16). All that is required is to

unfold the handle from your mower body

by lifting, until the handle ends snap into

the correct locations on the sides of your

mower body. Once this is complete the

wing nuts (15) can be tightened.

With the lower handle in position, assemble

the upper handle, as follows:

• Place the upper handle (11) over the

lower handle (10), with the upper bend

as shown in Fig. A.

• Align the lower holes in the upper handle

with the location pins (18) in the lower

handle and press the upper handle onto

these pins.

• Align the remaining (upper) holes in both

the upper and lower handles and fit a

bolt (17) through each hole. Fit a washer

(16) to each bolt and fit the wing nuts

(15) on to the bolts. Tighten each one

with hand pressure only.

Note: Do not use a spanner or other

implement to tighten the wing nuts.

When both upper and lower handle tubes

are assembled, fix the cable (19) by means

of the cable clips (12 &13) to the completed

handle, as follows:

• The lower cable clip (12) fits into the hole

in the lower handle tube (10) and has a

location pin for that purpose.

• The upper cable clip (13) fits onto the

upper handle tube (11) and can be

fitted in any position along the upper

side stem.

• Having completed the above, secure

the cable to the handle by pushing into

the clip lugs.

Height of cut adjustment (Fig. G)

Warning! Disconnect your mower from

the electrical supply before making any

adjustment and give the blade time to stop

rotating: cutting blades are sharp.

• Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug (see

below). Brown is for “Live” (L) and blue is

for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable directly

into your mower yourself. Instead, take your

mower to your nearest Black & Decker

service agent.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA) circuit breaker in the house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to your mower be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

your mower from the safety instructions and

safe working practices given in this manual.

Handle assembly (Fig. A - D)

Remove the parts from the carton and

familiarise yourself with the individual parts of

your mower.

The main parts of your mower are mower

body (1) which comprises the cutter deck (2),

cutter cover (3), collar (4), motor cover (5),

wheels (6), grassflap (7) and pivot pin (8).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GR350 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info