Bedienungsanleitung Black Decker GRC4736 TH1 (Seite 10 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

586112

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

ENGLISH

(Original instructions)

To remove the battery:

u Lift the battery lever (10) to release the battery clasp (9)

and then pull it back away from the battery pack. Lift the

battery pack out.

To t the battery

Before installation of the battery pack, make sure that the

mower is clear of debris and the charger connector (20) is

disconnected from the battery pack (11).

u Slide the battery pack into the mower. (the battery will only

t one way.)

u Secure the battery in the mower by clipping the battery

clasp (9) over the edge of the battery (11) and then push-

ing down the battery lever (10) until it clicks into place.

Use

Warning! Let the appliance work at its own pace. Do not

overload.

Charging the battery (g. J - L)

Note: Charge the battery before rst use.

The battery can either be removed from the mower for charg-

ing or can be charged while in place.

u Release the bail bar (3) to turn the lawnmower off, wait

until the blade stops and remove the safety key (1).

u Align the green (+) and white (-) connectors and insert the

charger plug (20) into the receptacle (22) on the mower or

remove the battery and insert the charger plug (20) into

the receptacle (21) on the battery.

u The charger connector (20) can only be plugged into the

mower receptacle one way.

u Insert the 240 Volt plug of the charger into a mains power

socket (g. L).

u The red light (26) on the charger (24) will come on to indi-

cate that the battery is being charged. If the red light is not

on, check that the charger connector is aligned correctly.

u When charging is complete the red light (26) will go off

and the green light will come on.

It will take approximately 16 hours to charge a fully discharged

battery.

It is recommended to leave the battery on permanent charge

between uses for optimum performance during the mowing

season.

The charger supplied with this product is intended to be

plugged in such that it is correctly orientated in a vertical or

oor mount position.

State of charge indicator (g. K)

The battery is tted with a state of charge indicator. This can

be used to display the current level of charge in the battery

during use.

u Press the state of charge indicator button (23).

Safety key

Remove the safety key:

u Whenever leaving the appliance unattended.

u Before cleaning a blockage.

u Before checking, cleaning or working on the appliance.

u After striking a foreign object.

u Whenever the appliance starts vibrating abnormally.

Switching on and off

Warning! Sharp moving blade. Never attempt to override the

operation of this switch and safety key system as a serious

injury could result.

Switching on (g. M)

u Insert the safety key (1) fully into the switch housing.

u Push the button (27) on the side of the switch housing.

u Pull the blade bail bar (3) toward the handle bar (5).

Switching off (g. M)

u To turn the lawnmower off, release the blade bail bar (3).

When the bail bar (3) has returned to the original position it

will activate the automatic braking mechanism. The motor is

electrically braked and the lawnmower blade will stop rotating

in 3 seconds or less.

Variable speed self drive (g. M)

Your lawnmower is equipped with variable speed self drive.

Self drive is independent from the blade On-Off switch. It

can be used with or without the blade spinning. For example,

when you have completed cutting your lawn, you can use the

self drive to propel the mower back to your storage location

without having the blade motor on.

To operate self drive without the blade spinning:

u Insert the safety key (1) fully into the switch housing.

u Push the self drive bail handle (2) to the handle bar (5).

u To turn the self drive off, release the self drive bail handle.

Note Self drive is variable speed. You can select the speed by

moving the selector lever (4). As you move the selector lever

forward, the speed will Increase. Moving the selector lever in a

reverse direction, will decrease the speed.

To operate self drive with the blade spinning:

u Insert the safety key (1) fully into the switch housing.

u Push the button (27) on side of switch housing, then pull

the blade bail handle (3) to the handlebar (5).

u Hold the blade bail handle in place against handlebar with

your right hand. Now push the self drive bail handle (2) to

the handlebar (5) with your left hand.

u You can hold both bail bars simultaneously against the

handlebar with your left hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GRC4736 TH1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GRC4736 TH1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info