Bedienungsanleitung Black Decker GRC730 (Seite 10 von 69) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

44141

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

We recommend that the steel blade is

sharpened or a new blade fitted at the

beginning of the season.

Replacement blades A6157 are available from

Black & Decker dealers and service centres.

Warning! When fitting a new blade use only

the Black & Decker replacement part

specified for your machine - do not attempt

to fit any other blade.

Fitting new blade (Fig. G)

Observe all the relevant warnings before

changing the blade.

Warning! Remove safety key before

changing the blade.

• Turn your machine over on its side so

that the underside of the cutter deck is

exposed.

• Wear gloves to protect hands.

• Using a cloth placed over the blade or

heavy duty gloves to protect your hands,

grip the blade and, using the spanner

provided, loosen and remove the nut

from the motor spindle. Turn the nut in an

anti-clockwise direction to loosen it.

• Remove nut (23), square washer (22),

clutch plate (21) and blade.

• To replace blade ensure the cutting

edges of the blade are closest to the

ground and place blade onto the

combined mount.

• Place the clutch plate over the shoulder

of the combined mount protruding

through the blade. Ensure to align the

inside edges with the outside edges of

the blade.

• Place the square steel blade spacer on

the motor shaft aligning the inside flats

with the shaft and engaging the outside

edges with the plastic clutch plate.

Engage nut on shaft and turn it

clockwise to tighten.

• Ensure that removed parts are replaced

correctly before use, incorrect assembly

may result in damage to your mower

and reduced cutting performance.

Note: This unit is fitted with a clutch plate

(24), between the blade nut and the blade,

which must be assembled correctly at all

times. Damaged blade assembly parts must

be replaced before use.

Overload protection

Your machine is fitted with overload protection.

If you work too quickly in long grass, or in heavy

cutting conditions, you may overload the motor.

This will be indicated by a significant drop in speed,

and eventually, the overload protection will operate.

This is not a fault but a safety device to protect

your machine.

When this occurs, remove the safety key and wait for

1 to 2 minutes to allow to cool, clear any blockage

ensuring the blade is free to rotate. To restart,

replace the safety key and operate the switch lever.

If the cut-out operates again within 10 minutes, you

should increase the height of cut (see “Height of

cut adjustment”).

Severe overloading may result in a longer delay on

restarting. In such cases, after resetting, you should

allow the motor to cool.

To obtain the best results:

• Cut the grass regularly.

• Do not cut wet grass.

• When the grass is longer than 10cm (4 inches),

it is advisable to go over the lawn on a high cut

setting and then finish using a lower setting.

Care and maintenance

The advice given in this section covers the general

care and maintenance of the main body of your

mower. Advice relating to the blades is given in

“Maintenance of blades”. Advice relating to the

maintenance and storage of the battery is given in

“Battery information”.

• Always keep your machine clean and free from

grass cuttings, especially the underside of the

cutter deck and the air vents.

• At the end of each cutting session we

recommend that the build up of grass on the

underside of the cutter cover is removed using a

blunt scraper, the spanner included with this

mower may be used for this purpose.

• Clean all plastic components with a damp cloth.

• Caution! Do not use solvents or cleaning fluids

as these may damage the plastic components of

your mower.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GRC730 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info