Bedienungsanleitung Black Decker GS1600 (Seite 12 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

55606

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Switching on and off (fig. C)

◆ To switch the tool on, set the on/off switch (1)

to position I.

◆ To switch the tool off, set the on/off switch to

position O.

Hints for optimum use

◆ Shred dry materials last, as this will help to

clear moist material from the shredder.

◆ Do not allow material to pile up and compost

prior to shredding.

◆ You may feed shreddings into the shredder for

a second time to further reduce their volume.

◆ Refer to the chart at the end of this text.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Before performing any maintenance,

switch off and unplug the tool.

◆ After use, open the chute as described below.

Clean and dry the casing and the blade area.

Avoid the blades.

◆ Store the tool in a dry place, out of children’s

reach.

◆ Regularly check that the blades are sharp.

Replacement blades are available from

Black & Decker repair agents.

To replace blades, proceed as instructed below.

Removing the chute (fig. D1 & D2)

You will need to remove the chute to obtain

access to the blade area.

Make sure that the tool is switched off and

unplugged.

◆ Loosen the thumb nut (7).

◆ Tilt the chute (3) backover (A), slide it forward (B)

and lift it upward (C).

◆ To replace the chute, proceed in reverse order.

Replacing the blades (fig. D1 - D4)

The blades can be used on both sides. When one

side has become blunt, you may use the other side.

◆ Make sure that the tool is switched off

and unplugged.

◆ Take care not to cut yourself.

Preferably wear gloves.

Removing

◆ Remove the chute as described above.

◆ Lock the blade disc using a block of wood (10)

as shown (fig. D3).

◆ Remove the blades (11) by loosening the Allen

screws (12) using the Allen key provided (fig. D4).

Refitting

To refit the blades:

◆ Place the blades on the disc with the ground

edge facing down. The holes in the blades

must line up with those in the disc.

◆ Securely fasten the blades (11) by tightening

the Allen screws (12).

◆ Remove the block of wood (10).

◆ Replace the chute (3) and tighten the thumb

nut (7) (fig. D1 & D2).

Restarting a clogged shredder

If the motor is overloaded, the tool will

automatically be switched off.

◆ Allow the motor to cool down for a few minutes.

If the motor still refuses to start:

◆ Make sure that the tool is switched off

and unplugged.

◆ Take care not to cut yourself. Preferably

wear gloves.

◆ Remove the chute as described above.

◆ Carefully remove all material from the shredder.

◆ Replace the chute as described above.

◆ Plug the tool in and switch it on.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GS1600 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info