Bedienungsanleitung Black Decker GSL700 (Seite 8 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

630499

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. When charging the battery for the rst

time, or after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles, the battery

will attain full capacity. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

The tool can be left connected to the charger indenitely.

To maximise the lifetime of the battery, it is recommended to

keep the battery connected to the charger whenever the tool

is not in use. When the battery is full, the power consumption

of the charger is negligible.

Charging with the wall mount (g. F)

u Place the tool on the wall mount (11).

u Plug in the charger.

Charging with the charger plug (g. G)

The charger plug is designed with lock outs to prevent the use

of an incorrect charger.

u Insert the charger plug (12) into the charger connector at

the rear of the tool.

u Plug in the charger.

GSL200/GSL300/GSL360 - Charging the battery

u Charge the battery.

When the battery is charging the charging indicator (6) lights

up. The charging indicator will go out when the charging is

complete.

GSL700 - Charging the battery

u Charge the battery.

When the battery is charging the charging indicator (6)

ashes. The charging indicator will stop ashing when the

charging is complete. The charging indicator ashes quickly to

indicate a charging problem. When a charging problem

occurs, connect the tool directly to the charger plug by

removing the wall mount. If the charging problem still occurs,

the charger must be disconnected from the mains supply and

taken to an authorised service centre for repair.

Switching on and off (g. H)

Switching on

u Push and hold the lock button (2) to the right or to the left

and then squeeze the on/off switch (1).

u Release the lock-off button.

Switching off

u Release the on/off switch (1).

Warning! Never attempt to lock the switch in the on position.

Hints for optimum use (g. I & J)

u Spray the blade with a light coating of light general use oil

before first use and whenever the blades begin to look dry.

Trimming grass

u In order to achieve optimum cutting results, only cut dry

grass.

u Hold the tool as shown in fig. I. Keep your other hand well

away from the blade. Maintain a stable working position so

that you do not slip. Do not overreach.

u When cutting long grass, work in stages from the top.

Take small cuts.

u Keep the tool away from hard objects and delicate plants.

u If the tool starts running slowly, reduce the load.

u To make a closer cut, slightly tilt the tool.

Trimming hedges

u Slightly tilt the tool (up to 15° relative to the line of cut) so

that the blade tips point slightly towards the hedge (fig. J).

This will cause the blades to cut more effectively.

u Start by trimming the top of the hedge. Hold the tool at the

desired angle and move it steadily along the line of cut.

The double-sided blade allows you to cut in either

direction.

u In order to obtain a very straight cut, stretch a piece of

string along the length of the hedge at the desired height.

Use the string as a guideline, cutting just above it.

u In order to obtain flat sides, cut upwards with the growth.

Younger stems move outwards when the blade cuts

downwards, causing shallow patches in the hedge.

u Take care to avoid any foreign objects. Especially avoid

hard objects such as metal wire and railings, as these

could damage the blades.

u Regularly oil the blades.

Guidelines for trimming (UK & Ireland)

u Trim hedges and shrubs with seasonal leaves (new leaves

every year) in June and October.

u Trim evergreens in April and August.

u Trim conifers and other fast growing shrubs every six

weeks from May until October.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GSL700 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info