Bedienungsanleitung Black Decker GT200 series (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

665758

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

terminal screws

clamping washers

connector body fixing screw

6mm

cable

clamp cover

cable

protector

Assembly instructions

• To avoid risk of injury, it is advisable to leave the

blades in their cardboard cover until the front

handle has been fitted.

You will need a No 2 Posidrive screwdriver.

Fitting the front handle

(Please see diagram 2)

• Clamp the handle (1) into the recesses (2) on the

side of the unit.

• Pass the large screws (3) through the handle into

the body, and tighten.

Fitting the guard

(Please see diagram 3)

• Slide the guard over the length of the blade and

locate onto the recesses on the side of the body.

• Insert the two guard fixing screws through the

sides of the guard into the unit body and tighten.

Note: The guard and handle must always be fitted to

the unit for protection of the user.

Operation of your hedgetrimmer

(Please refer to diagram 4)

• Models with lock-off switch:

• TO SWITCH ON

• Press in lock-off button (A) and squeeze the

trigger (B)

• TO SWITCH OFF

• Release the trigger.

• For units with a brake mechanism:

• SWITCHING ON

• The motor may start momentarily before

the blades begin to move. By fully depressing

the switch trigger, drive to the blades will

be connected and then the blades will begin

to move.

• SWITCHING OFF

• The motor may run on after the blades have

stopped. This is perfectly normal.

Electronic (

Please see diagram

• Models with electronic speed control:

Alter the speed to suit the application -

Low speed for light trimming.

High speed for fast hedge trimming.

Switch off before changing speed settings.

The speed of the blades can be adjusted from High

speed to Low speed by rotating the control knob.

Low speed is obtained when No. 1 on the knob

is visible.

High speed is obtained when No. 2 on the knob

is visible.

Cutting techniques for better results

(Please see diagrams 6.1 to 6.5)

• The blades will cut most effectively when they are

not exactly parallel with the line of cut, but have

the tips of the blades pointing slightly towards

the hedge. This lateral tilt should not exceed 5

the line of cut.

• Most users trim the top of a hedge first. Hold the

tool at the desired angle and move it steadily

along the line of cut. The double edged blade

enables you to cut in either direction or with a

side to side movement.

• For a very level finish, a piece of string can be

stretched along the length of the hedge at the

required height to serve as a guide. The hedge

may be cut just above the string.

• To keep very flat sides it is better to cut upwards

with the growth. Cutting downwards can

produce an uneven result.

• Take care to avoid hard objects, such as wire,

which could cause damage to cutting blades.

Remember that your hedgetrimmer is also suitable

for clipping most shrubs or brambles.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GT200 series Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info