Bedienungsanleitung Black Decker GWC54PCB (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709456

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

Leaving the battery in the charger

The charger (5) and battery pack (4) can be left connected

with the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a

service center for recycling.

State of charge indicator (Fig.B)

The battery is equipped with a state of charge indicator.

This can be used to display the current level of charge in the

battery during use and during charging. It does not indicate

tool functionality and is subject to variation based on product

components, temperature and end-user application.

Checking state of charge during use

u Press the state of charge indicator button (B1).

u The three LEDs (B2) will illuminate, indicating the percent

of charge in the battery. See chart in gure B.

u If LED light does not illuminate, charge battery.

Charger Diagnostics (Fig.E)

Refer to the indicators in gure E for the charge status of the

battery pack.

Bad Battery

If you see a bad battery blink pattern, do not continue

to charge this battery. Return it to a service center or a

collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life. A cold battery pack will charge at a

slower rate than a warm battery pack. The pack will charge at

that slower rate throughout the entire charging cycle and will

not return to maximum charge rate even if the pack warms.

Installing and removing the battery pack from the

tool

To install battery pack Fig. C)

u Insert battery (4) into battery housing until an audible click

is heard (Figure. C)

u Ensure battery pack is fully seated and fully latched into

position.

To remove battery pack (Fig.D)

u Depress the battery release button (4a) as shown in gure

D and pull battery pack (4) out of battery housing.

DUALVOLT 54V Battery Pack (Fig F.)

The DUALVOLT 54V battery pack can be used on 54V &

18V Black+Decker Cordless tools. The battery can recognise

the tool it is inserted into and will run at the relevant power,

providing longer runtime in 18V tools. There is a State of

charge button (4b) which will indicate the level charge at both

54V & 18V.

Operation

Warning! Always wear safety glasses. Wear a lter mask if

the operation is dusty. Use of gloves, long pants and substan-

tial footwear is recommended. Keep long hair and loose cloth-

ing away from openings and moving parts. THIS SWEEPER

IS FOR HOUSEHOLD USE ONLY.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GWC54PCB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info