Bedienungsanleitung Black Decker GX530 T8 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

586102

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

• On long grass, above 10cm (4 inches), use two

cuts to get a close finish. We recommend that

the first cut should be taken with the blade set at

maximum height of cut and the second taken

with it set at medium or close. This will prove to

be easier and give a better overall finish to

your lawn.

Care and maintenance

The advice given in this section covers the

general care and maintenance of the main

body of your mower. Advice relating to the

blades is given in “Maintenance of blades”.

Warning! Do not use an extension cable

which shows signs of damage. Fit a new

cable completely - do not make any

permanent or temporary repairs.

• Always keep your mower clean and free

from grass cuttings, especially the

underside of the cutter cover and the air

vents.

• Check all electrical cables at regular

intervals, looking for signs of wear,

abrasion or other damage.

• At the end of each cutting session we

recommend that the build up of grass on

the underside of the cutter cover is

removed using a blunt scraper or the

spanner supplied.

• Remove grass cuttings from the slot

between the pivot block flanges.

• Clean all plastic components with a

damp cloth.

Caution: Do not use solvents or cleaning

fluids as these may damage the plastic

components of your mower.

Fault finding

If your mower does not operate correctly,

use the following table to locate the problem.

Warning! Always disconnect your mower

from the electrical supply before carrying out

any inspection.

Symptoms Possible cause Remedy

Motor buzzes Blade jammed. Disconnect from

but blade does the electrical

not move. supply.

Remove the

obstruction from

the blade.

No noise and Faulty electrical Disconnect from

the blade does connection. the electrical

not move. supply.

Symptoms Possible cause Remedy

No noise and Faulty electrical Plug your mower

the blade does connection. into an alternative

not move. compatible

electrical supply.

Check if a new

fuse is required.

Re-tighten and

check all electrical

connections in the

extension cables.

Overload cut- Reset overload

out operates. cut-out.

Grass not being The grassbox Empty the

picked up. is full. grassbox.

The pickup inlet Remove grassbox

in the grassbox and clear the hole

is blocked. in the base.

Air paths are Remove grassbox

blocked. and clear the filter

in the roof of the

grassbox.

Also clean the

filter on the back

of your mower.

The cut height Disconnect from

is too low in the electrical

long grass. supply. Reset

the blade height

to a higher

position.

Your mower Push your mower

is being moved in a straight line to

side to side. maximise pick up.

Motor stalled. The motor is Disconnect from

overloading in the electrical

long, thick supply. Reset the

grass. blade height

to a higher

position.

Poor cutting Blade damaged Disconnect from

performance. due to impact the electrical

on large stones, supply. Check the

tree stumps, blade for damage.

paving stones or Replace with a

similar objects. new blade,

if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GX530 T8 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info