Bedienungsanleitung Black Decker GX530 (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

474473

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Your switch box incorporates a cable

restraint. To fix the cable to the restraint,

proceed as follows:

• Bring the socket end of the extension

cable from behind and connect it to your

mower plug.

• Form a loop on your extension cable

close to the coupler (Fig. E).

• Push the loop through the slot from the

opposite side of the restraint hook,

position the loop over the hook and pull

the cable back through the slot. Your

cable will now be restrained.

• The extension cable should now fall

away from your mower and behind the

operator, ready for use.

Warning! Do not attempt to operate your

mower with one hand - you must guide it

with both hands.

• Lift the handle up to release it from the

park position.

• Proceed down the cutting area as shown

in Fig. Ja, working from position 1

towards position 2 and, on reaching

position 2, turn to the right and proceed

towards position 3. Continue to the end

of the cutting area, turn to the left, and

proceed towards position 4. Continue in

the same manner as shown in Fig. Ja,

always working away from the cable. Do

not adopt the method shown in Fig. Jb,

working towards the cable, as this can

be dangerous.

• For best grass pick-up, push your

mower in straight lines.

Your mower will continue to operate whilst

you are pressing the switch lever. If you

release it for any reason you will not be able

to press it again until you have pressed the

safety lock-off button on the switch box.

This feature prevents accidental restart.

When you have finished using your mower

we recommend that you clean all debris from

it before putting it away. Refer to the “Care

and maintenance” section.

Note: To obtain the best results cut your

lawn or grassed area regularly and do not

cut when the grass is wet.

Overload protection (GX635 only)

Your mower is fitted with overload protection.

The reset button (25) can be found on the switch box

(Fig. A).

If you work too quickly in long grass, or in heavy

cutting conditions, you may overload the motor.

This will be indicated by a significant drop in speed,

and eventually the overload protection will operate.

This is not a fault but a safety device to protect

your mower.

When this occurs, release the switch and wait for

2 to 3 minutes to allow the motor to cool, then press

the reset button (25) and restart by operating the

switch lever and lock-off button.

If the cut-out operates again within 10 minutes you

should increase the height of cut (see “Height of cut

adjustment”) and walk more slowly.

Severe overloading may result in a longer delay on

restarting. In such cases, after resetting, you should

allow the motor to cool.

Blade maintenance

The steel blade is designed to give a fine

finish in long or tough grass. The blade will

continue to cut even when it has become

blunt or burred. There is no need for it to be

razor sharp.

If, however, because of damage or wear the

cutting performance deteriorates, then your

mower may require a new blade, or at least

the existing blade to be sharpened.

We recommend that the steel blade is

sharpened or a new blade fitted at the

beginning of each season.

Replacement blades (cat. no. A6184) are

available from Black & Decker service agents.

Warning! When fitting a new blade use only

the Black & Decker replacement part

specified for your mower - do not attempt to

fit any other blade.

Fitting a new blade

Observe all the relevant warnings before

changing blades.

Details on the fitment of new steel blades are

given in “Cut height adjustment”.

Handy hints

• Before starting your mower on grass always tilt it

to one side slightly and allow it to run up to

maximum speed before commencing to cut the

grass. This will maximise the hover effect and will

prevent the blades from digging into the grass.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GX530 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GX530

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info