Bedienungsanleitung Black Decker hp 9096 (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

386448

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

◆ Under extreme conditions, battery leakage may occur.

When you notice liquid on the battery, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin

contact.

- In case of skin or eye contact, follow the instructions

below.

Warning! The battery fluid, a 25-30% solution of potassium

hydroxide, can be harmful. In case of skin contact, immediately

rinse with water. Neutralise with a mild acid such as lemon

juice or vinegar. In case of eye contact, rinse abundantly with

clean water for at least 10 minutes. Consult a physician.

◆ Do not incinerate the battery.

◆ Do not attempt to charge damaged batteries.

Chargers

◆ Use your Black & Decker charger only to charge the battery

in the tool with which it was supplied. Other batteries

could burst, causing personal injury and damage.

◆ Never attempt to charge non-rechargeable batteries.

◆ Have defective cords replaced immediately.

◆ Do not expose the charger to water.

◆ Do not open the charger.

◆ Do not probe the charger.

The charger is intended for indoor use only.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

Overview (fig. A)

1. Variable speed switch

2. Forward/reverse slider

3. Bit holder sleeve

4. Head adjustment button

5. Charger connector

6. Charger

7. Charger plug

8. Screwdriver bit

9. Battery cover

Assembly

Fitting and removing a drill bit or screwdriver bit

(fig. B & D)

This tool uses screwdriver bits and drill bits with a 1/4"

(6.35) mm hexagonal shank.

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position (fig. D).

◆ Pull back the bit holder sleeve (3) (fig. B).

◆ Insert the bit shaft (8) into the bit holder.

◆ Release the bit holder sleeve.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Charging the battery (fig. A)

The battery needs to be charged before first use and whenever

it fails to produce sufficient power on jobs that were easily

done before. A new battery or a battery that has not been

used for a long period of time achieves full performance only

after approximately 5 charging and discharging cycles.

After normal use, a charging time of 3 hours will enable the

tool to operate at an effective power level for most tasks.

However, further charging for up to 6 hours could significantly

increase the run time, depending on the battery and charging

conditions. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery, insert the charger plug (7) into the

connector (5).

◆ Plug in the charger. Switch on at the mains.

◆ Leave the tool connected to the charger for 3-6 hours.

The charger may hum and become warm while charging; this

is normal and does not indicate a problem.

◆ Before using the tool, unplug the charger and disconnect

the tool from the charger.

Warning! Do not use the tool while it is connected to the charger.

Adjusting the head (fig. C)

For optimum versatility, the head can be set to different positions.

◆ Press the head adjustment button (4) down.

◆ Swivel the head into the desired position.

◆ Release the button.

Selecting the direction of rotation (fig. D)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker hp 9096 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info