Bedienungsanleitung Black Decker HP188 (Seite 12 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

472990

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

Large screws and hard workpiece materials require a

higher torque setting than small screws and soft

workpiece materials. The collar has a wide range of

settings to suit your application.

◆ For drilling in wood, metal and plastics, set the

collar (3) to the drilling position by aligning the

symbol

with the marking (24).

◆ HP148F2/HP188F2:

For drilling in masonry, set the collar (3) to the

hammer drilling position by aligning the

symbol with the marking (24).

◆ For screwdriving, set the collar to the desired

setting. If you do not yet know the appropriate

setting, proceed as follows:

◆ Set the collar (3) to the lowest torque setting.

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired

result is achieved, increase the collar setting

and continue tightening the screw.

Repeat until you reach the correct setting.

Use this setting for the remaining screws.

Two-gear selector (fig. I)

◆ For drilling in steel and for screwdriving

applications, slide the two-gear selector (5)

towards the front of the tool (1st gear).

◆ For drilling in materials other than steel, slide

the two-gear selector (5) towards the rear of

the tool (2nd gear).

Drilling/screwdriving (fig. A)

◆ Select forward or reverse rotation using the

forward/reverse slider (2).

◆ To switch the tool on, press the switch (1).

The tool speed depends on how far you press

the switch.

◆ To switch the tool off, release the switch.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line

with the drill bit.

◆ Just before the drill tip breaks through the

other side of the workpiece, decrease pressure

on the tool.

◆ Use a block of wood to back up workpieces

that may splinter.

◆ Use spade bits when drilling large diameter

holes in wood.

◆ Use HSS drill bits when drilling in metal.

◆ Use masonry bits when drilling in soft masonry.

◆ Use a lubricant when drilling metals other than

cast iron and brass.

◆ Make an indentation using a centre punch at

the centre of the hole to be drilled in order to

improve accuracy.

Screwdriving

◆ Always use the correct type and size of

screwdriver bit.

◆ If screws are difficult to tighten, try applying a

small amount of washing liquid or soap as a

lubricant.

◆ Always hold the tool and screwdriver bit in a

straight line with the screw.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Your charger does not require any maintenance

apart from regular cleaning.

Before performing any maintenance on

the tool, remove the battery from the tool.

◆ Unplug the charger before cleaning it.

◆ Regularly clean the ventilation slots in your tool

and charger using a soft brush or dry cloth.

◆ Regularly clean the motor housing using a

damp cloth. Do not use any abrasive or

solvent-based cleaner.

◆ Regularly open the chuck and tap it to remove

any dust from the interior.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker HP188 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info