Bedienungsanleitung Black Decker HPL106 (Seite 6 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

472992

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

(Original instructions)

u To remove the battery, push the release buttons (12) while

at the same time pulling the battery out of the receptacle.

Fitting and removing a drill bit or screwdriver bit

(g. D)

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Grasp the chuck (3) and rotate it in the counterclockwise

direction, as viewed from the chuck end.

u Insert the bit shaft (13) into the chuck.

u Firmly tighten the chuck by rotating it in the clockwise

direction as viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories in this manner.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (5), insert it into the charger (10).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (11) will ash green continuously

(slowly).

The charge is complete when the charging indicator (11)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging indica-

tor (11) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (11) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (5).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

service centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Selecting the direction of rotation (g. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque

This tool is tted with a collar to set the torque for various

screwdriving and drilling applications. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. For the denition of the

symbol refer to the listing below.

u For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the

symbol.

u For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

- Set the torque adjustment collar (4) to the lowest torque

setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker HPL106 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info