Bedienungsanleitung Black Decker HPL108 TH1 (Seite 8 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581139

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

(Original instructions)

Fitting and removing the accessories (g. C - H)

Warning! Before tting an accessory, disconnect the tool from

the mains supply.

Fitting a Black & Decker / Piranha accessory (g. C - E)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Slide the accessory (13) between the shaft and the acces-

sory holder making sure the accessory engages all eight

pins on the holder and is ush with the shaft.

u Release the accessory clamping lever.

Note: Some accessories, such as scrapers and blades can be

mounted at an angle if required (g. E).

Removing a Black & Decker / Piranha accessory (g. C)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Pull the accessory from the tool making sure the acces-

sory dis-engages from all eight pins on the holder.

u Release the accessory clamping lever.

Warning: Gloves must be worn when removing accessories

as they may become hot during use.

Fitting a sanding sheet (g. F)

u Line up the sanding sheet (14) with the sanding base (6)

as shown.

u Press the sheet rmly and evenly onto the sanding base,

making sure that the holes in the sheet coincide with the

holes in the base.

Removing a sanding sheet

u Pull the sanding sheet (14) off the sanding base (6).

Warning! Never use the sanding base without a sanding

sheet or accessory in place.

Fitting the dust extraction adaptor (g. G) (Where

supplied - Accessory part number : 'Item 58 from the

service sheet found at the end of this instruction manual')

u Line up the dust extraction adaptor (7) with the sanding

base (6) as shown.

u Press the adaptor rmly and evenly in to the sanding

base.

u Secure the adaptor by turning the locking nut (17) clock-

wise.

u Connect a vacuum cleaner to the dust extraction adaptor.

Removing the dust extraction adaptor

u Turn the locking nut (17) anti-clockwise.

u Pull the dust extraction adaptor (7) out of the sanding

base (6).

Fitting alternative accessories (g. H)

u Place the spacer (8) onto the collar (15).

u Place the alternative accessory (16) onto the collar (15).

u Firmly attach the xing bolt (9) into place to ensure a tight

t for the alternative accessory (16).

Note: The spacer and xing bolt are not used to attach Black

& Decker accessories. Black and Decker accessories are

attached using the Super-lok

Tool free accessory clamping

lever.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before cutting into walls, oors or ceilings, check for

the location of wiring and pipes.

Charging the battery (g. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (4), insert it into the charger (10).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (11) will ash green continuously

(slowly).

The charge is complete when the charging indicator (11)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops off the battery charge. The charging indica-

tor (11) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker HPL108 TH1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker HPL108 TH1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info