Bedienungsanleitung Black Decker ka 230 ekw (Seite 28 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

389571

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

the allen key provided. Press the base on firmly when

tightening the screw.

REVERSING THE POINTED BASE

(KA210/KA210E/KA220/KA220E/KA230E)

Proceed as follows:

Disconnect the plug from the electricity supply.

Turn the screw

anticlockwise using the

allen key provided in

the handle. Remove the

screw and the washer

from the spindle. Hold

the base in position

with the point facing

rearwards. Fit the

washer and the screw. Tighten the screw using the

allen key provided. Press the base on firmly when

tightening the screw.

FITTING THE SANDPAPER (POINTED BASE)

Proceed as follows:

Disconnect the plug from the electricity supply.

Detach the two

diamond-shaped tips

from the main sheet.

Place the sandpaper on

the pointed base, making

sure the holes of the

paper and the base are

aligned. Never use your

multi sander without

sandpaper and always

use a full sheet of sandpaper.

TIP COMPONENTS (POINTED BASE)

(KA210/KA210E/KA220 /KA220E/KA230E)

Each sheet of

sandpaper has a

removable tip, with two

spare tips attached. To

obtain maximum use

from each sheet, detach

and turn the tip when the

front part is worn.

When the whole tip is worn, replace it with one of the

spare tips provided. The tip of the backing pad is

removable. When the front part is worn, turn the tip.

When the tip is completely worn, replace the tip. Spare

tips are available as accessories. When the tip of the

hard plastic tip holder is worn, remove the screw and

turn the holder. Spare holders are available as accessories.

FITTING THE PROFILE BASE (KA230E)

Proceed as follows:

Disconnect the plug from the electricity supply.

Position the profile

base on the spindle,

with the long section

pointing towards the

front of your sander.

Make sure the legs fit

into their housings.

Place the washer in

position on the base

and fit the screw using

the allen key provided.

Press the base on

firmly when tightening the screw.

FITTING THE SANDING PROFILE (KA230E)

Proceed as follows:

Disconnect the plug from the electricity supply.

There are six sanding

profiles supplied, each

being different in size

and shape. Select the

sanding profile most

suitable for the task

and push into the slot in

the front of the base.

To do this, first locate

one end of the sanding

profile into the recess

at the back of the

profile base slot, then

push the other end so

that it locates in the

recess in the front of

the profile base. The sanding profile will now be

positively located. The sanding profile can be removed

by depressing the small black square section which is

visible at the front of the profile base, whilst pulling the

profile away from its locating slot.

FITTING THE SANDING PAPER (PROFILE BASE)

(KA230E)

Proceed as follows:

Disconnect the plug from the electricity supply.

With the profile fitted in the base, fit the paper by

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ka 230 ekw Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info