Bedienungsanleitung Black Decker ka 320 eka (Seite 7 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

389517

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). Before use,

inspect the extension cable for signs of damage, wear and

ageing. Replace the extension cable if damaged or

defective. When using a cable reel, always unwind the

cable completely. Use of an extension cable not suitable

for the power input of the tool or which is damaged or

defective may result in a risk of re and electric shock.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust extraction outlet

3. Sanding base

4. Paper clamp lever

5. Variable speed control knob

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingsandingsheets(g.A&B1-B3)

Warning! Never use the tool without a sanding sheet or

accessory in place.

Fittingsandingsheetswithnylonloops(g.A)

u Make sure that the tool is switched off and unplugged.

u Press the sheet rmly and evenly onto the sanding base

(3), making sure that the holes in the sheet line up with the

holes in the base.

Fittingregularsandingsheets(g.B1-B3)

u Make sure that the tool is switched off and unplugged.

u Soften the sanding sheet by rubbing its non-abrasive side

over the edge of a worktop.

u Press the paper clamp levers (4) upwards to release them

from the retaining grooves and open the paper clamps by

pressing them down (g. B1).

u Place the sheet onto the sanding base (3), making sure

that the holes in the sheet line up with the holes in the

base (g. B2).

u Insert the edge of the sanding sheet into the front paper

clamp as shown (g. B3).

u Press the front paper clamp lever (4) downwards and

locate it in the retaining groove.

u While keeping a slight tension on the sheet, insert the rear

edge of the sheet into the rear paper clamp.

u Press the rear paper clamp lever (4) downwards and

locate it in the retaining groove.

Fittingandremovingthedustbag(g.C)

u Fit the dustbag (6) over the dust extraction outlet (2).

u Slide the dustbag onto the tool and make sure that it is

securely located.

u To remove the dustbag, pull it to the rear and off the outlet.

Use

Warning! Let the tool work at its own pace. Do not overload.

KA320E - Variable speed control

The variable speed control allows you to adapt the speed of

the tool to the workpiece material.

u Set the control knob (5) to the desired setting. Use a high

speed for wood, medium speed for veneer and synthetics

and low speed for acrylic glass, non-ferrous metals and for

removing paints.

Switchingonandoff(g.D)

u To switch the tool on, press the front part I of the on/off

switch (1).

u To switch the tool off, press the rear part O of the on/off

switch.

Emptyingthedustbag(g.C)

The dustbag (6) should be emptied every 10 minutes of use.

u Pull the dustbag (6) to the rear and off the tool.

u Hold the spout down and shake the dustbag (6) to empty

the contents.

u Slide the dustbag (6) onto the tool and make sure that it is

securely located.

Hintsforoptimumuse(g.E)

u Always hold the tool with both hands.

u Do not exert too much pressure on the tool.

u Regularly check the condition of the sanding sheet.

Replace when necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ka 320 eka Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info