Bedienungsanleitung Black Decker ka 400 (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

390043

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Labels on tools

The following pictograms are shown on the tool:

Electrical safety

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. On/off switch

2. Dustbag

3. Dust extraction outlet

4. Sanding base

5. Paper clamp lever

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting sanding sheets (fig. A & B)

Warning! Never use the tool without a sanding sheet or

accessory in place.

Fitting sanding sheets with nylon loops (fig. A)

Warning! Make sure that the tool is switched off and

unplugged.

 Press the sheet firmly and evenly onto the sanding

base (4), making sure that the holes in the sheet line up

with the holes in the base.

Fitting regular sanding sheets (fig. B)

Warning! Make sure that the tool is switched off and

unplugged.

 Soften the sanding sheet by rubbing its non-abrasive

side over the edge of a worktop.

 Press the paper clamp levers (5) upwards to release

them from the retaining grooves and open the paper

clamps (5) by pressing them down.

 Place the sheet onto the sanding base (4).

 Insert the edge of the sanding sheet into the front paper

clamp (5) as shown.

 Press the front paper clamp lever (5) downwards and

 locate it in the retaining groove.

 While keeping a slight tension on the sheet, insert the

 rear edge of the sheet into the rear paper clamp (5).

 Press the rear paper clamp lever (5) downwards and

locate it in the retaining groove.

Louvre attachment (fig. C) (KA400L only)

With this attachment you can work in crevices and use the

sanding base on both sides.

 Locate the front of the louvre attachment (7) onto the

sanding base (4).

 Secure it in position with the four screws supplied.

 Place a 1/2 sheet to the underside of the louvre base.

Part of it will fold over the front part of the base.

 To remove the louvre attachment (7), reverse the

procedure.

Fitting and removing the dustbag (fig. D)

 Fit the dustbag (2) over the dust extraction outlet (3).

 Slide the dustbag (2) onto the tool and make sure that it

is securely located.

 To remove the dustbag (2), pull it to the rear and off the

outlet.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These include:

 Injuries caused by touching any rotating/moving parts.

 Injuries caused when changing any parts, blades or

accessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods make sure you take

regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF).

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off (fig. E)

 To switch the tool on, press the part of the on/off switch

(1) marked 'I'.

 To switch the tool off, press the part of the on/off switch

(1) marked '0'.

Emptying the dustbag

 The dustbag (2) should be emptied every 10 minutes.

 Shake the dustbag (2) to empty the contents

Warning! To reduce the risk of injury, the user must

read the instruction manual.

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ka 400 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info