Bedienungsanleitung Black Decker KA293E T2 (Seite 10 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

578032

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

◆ Place the sanding belt (12) over the front

pulley (13) and the rear pulley (14), sliding it

through the slot in the housing.

◆ Move the belt tensioning lever (5) to the rear

position (B).

◆ Adjust the belt tracking as described below.

Removing

◆ Move the belt tensioning lever (5) to the front

position (A).

◆ Slide the sanding belt (12) off the pulleys.

Adjusting the sanding belt tracking (fig. D)

◆ Switch the tool on.

◆ Turn the belt tracking knob (6) as required until

the sanding belt runs straight along the length

of the arm.

Fitting and removing the dustbag (fig. E)

Make sure to remove the dustbag before

using the tool on metal workpieces.

Fitting

◆ Align the dustbag (8) with the tool as shown.

◆ Slide the dustbag onto the tool until it clicks

into place.

Removing

◆ Pull the dustbag (8) to the rear and off the tool.

USE

Let the tool work at its own pace.

Do not overload.

Variable speed control (fig. F)

The variable speed control allows you to adapt the

speed of the tool to the workpiece material. Use a

low speed setting when using a fine grit, when

working with plastics or ceramics and when

removing painted or varnished surfaces. Use a

high speed setting when using a coarse grit and

when removing a lot of material.

◆ Set the control knob (7) to the desired setting.

Switching on and off (fig. G)

◆ To switch the tool on, press the on/off switch (1).

◆ To switch the tool off, release the on/off switch.

◆ For continuous operation:

- Press the on/off switch (1).

- Press the lock-on button (2).

- Release the on/off switch.

◆ To switch the tool off when in continuous

operation, press and release on/off switch (1).

Emptying the dustbag (fig. E)

The dustbag should be emptied every 10 minutes

of use.

◆ Pull the dustbag (8) to the rear and off the tool.

◆ Hold the spout down and shake the dustbag

to empty the contents.

◆ Refit the dustbag onto the tool.

If necessary, the dustbag can be removed from its

frame and washed. Let it dry before refitting it.

Special applications

Cranked arm (fig. H)

◆ Use section A for grooving or sanding in the

centre of workpieces and in confined areas.

Use section B for curved surfaces.

Straight arm (fig. I)

◆ Use the normal or narrow arm for general use,

for slotting and for making joints.

Narrow arm (fig. J)

◆ Use the narrow arm for finer detail, for cutting

and for carving.

Hints for optimum use

◆ Always hold the tool with both hands.

◆ Do not exert too much pressure on the tool.

◆ Regularly check the condition of the sanding

belt. Replace when necessary.

◆ Always sand with the grain of the wood.

◆ When sanding new layers of paint before

applying another layer, use extra fine grit.

◆ On very uneven surfaces, or when removing

layers of paint, start with a coarse grit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KA293E T2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KA293E T2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info