Bedienungsanleitung Black Decker ka900e (Seite 8 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

390169

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

Your tool has some or all of the following features:

1. Variable speed control knob

2. On/off switch

3. Lock-on button

4. Secondary handle

5. Belt tensioning lever

6. Belt tracking knob

7. Straight arm

Fig. A

9. Narrow arm

10. Cranked arm

Fig. D

13. Dustbag

14. Dust cassette

15. Deflector

Assembly

Warning! Before assembly, make sure that the tool is switched

off and unplugged.

Fitting and removing sanding arms (fig. A)

Before first use, you must fit a sanding arm to the tool. Your

tool is supplied with the following:

 A straight arm (7, sanding width 13 mm).

 a narrow arm (9, sanding width 6 mm) for intricate work.

 a cranked arm (10) for grooving and sanding in the centre

of workpieces and for reaching confined areas.

These parts are also available as an accessory from your

Black & Decker dealer, (not available in Australia and New

Zealand).

Fitting

 Make sure that the belt tensioning lever (5) is in the position

shown.

 Loosen and remove the belt tracking knob (6).

 Remove the tape retaining the spring (8) (if present).

 Check that the spring (8) is located in its mounting hole.

 Position the arm (7, 9 or 10) as shown.

 Fit the belt tracking knob (6) and tighten it until the arm (7)

is aligned with the tool.

Removing

 Remove the sanding belt (12) (if present) as described

 below.

 Loosen and remove the belt tracking knob (6).

 Remove the arm (7, 9 or 10).

Warning! Be careful not to lose the spring (8).

Fitting and removing sanding belts (fig. B)

Warning! The spring must be fitted. Be careful not to lose the

spring (8).

Fitting

 Move the belt tensioning lever (5) to the front position (A).

 .Make sure that the arrows on the inside of the sanding belt

(12) face the same direction as the arrows (17) on the

housing.

 Place the sanding belt (12) over the front pulley (11) and

the rear pulley (16), sliding it through the slot in the housing.

 Move the belt tensioning lever (5) to the rear position (B).

 Adjust the belt tracking as described below.

Removing

 Move the belt tensioning lever (5) to the front position (A).

 Slide the sanding belt (12) off the pulleys.

Adjusting the sanding belt tracking (fig. C)

 Switch the tool on.

 Turn the belt tracking knob (6) as required until the sanding

belt runs straight along the length of the arm.

Fitting and removing the dust cassette or the dust bag

(fig. D, E and F)

Warning! Always remove the dustbag or dust cassette and fit

the deflector when using the tool on metal workpieces.

Fitting

 Fit the dust cassette (14) or the dust bag (13) over the dust

extraction outlet.

 Slide the item (13 or 14) onto the tool and make sure that it

is securely located.

Removing

 To remove the dust cassette (14), or the dust bag (13), pull

the item (13 or 14) to the rear and off the outlet.

Fitting and removing the deflector (fig. D and E)

Warning! The deflector must be used when sanding metal

workpieces.

Fitting

 Fit the deflector (15) over the dust extraction outlet.

 Slide the deflector (15) on to the tool and make sure that it

is securely located.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ka900e Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info