Bedienungsanleitung Black Decker KA902E T1 (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578034

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Fit the dustbag or dust cassette before using the tool

on wooden workpieces.

Remove the dustbag or cassette and t the deector

before using the tool on workpieces containing

metal.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

Your tool has some or all of the following features:

1. On/off switch

2. Variable speed control knob

3. Lock-on button

4. Secondary handle

5. Belt tensioning lever

6. Belt tracking knob

7. Straight arm

Fig. A

8. Narrow arm

9. Cranked arm

Fig. D

10. Dust cassette

11. Deector

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingandremovingsandingarms(g.A&B)

The tool is supplied with the following sanding arms:

u Straight arm (7), sanding width 13 mm

u Narrow arm (8), sanding width 6 mm, for intricate work

u Cranked arm (9) for grooving and sanding in the centre of

workpieces and for reaching conned areas

Before rst use, you must t the sanding arm to the tool.

Fitting

u Make sure that the belt tensioning lever (5) is in the

position shown.

u Loosen and remove the belt tracking knob (6).

u Remove the tape retaining the spring (12) (if present).

u Check that the spring (12) is located in its mounting hole.

u Position the arm as shown.

u Fit the belt tracking knob (6) and tighten it until the arm (7)

is aligned with the tool.

Removing

u Remove the sanding belt (13) (if present) as described below.

u Loosen and remove the belt tracking knob (6).

u Remove the arm.

Warning! Be careful not to lose the spring (12).

Fittingandremovingsandingbelts(g.B)

Warning! The spring must be tted. Be careful not to lose the

spring (12).

Fitting

u Move the belt tensioning lever (5) to the front position (A).

u Make sure that the arrows on the inside of the sanding

belt (13) face the same direction as the arrows (14) on the

housing.

u Place the sanding belt (13) over the front pulley (15) and

the rear pulley (16), sliding it through the slot in the

housing.

u Move the belt tensioning lever (5) to the rear position (B).

u Adjust the belt tracking as described below.

Removing

u Move the belt tensioning lever (5) to the front position (A).

u Slide the sanding belt (13) off the pulleys.

Adjustingthesandingbelttracking(g.C)

u Switch the tool on.

u Turn the belt tracking knob (6) as required until the

sanding belt (13) runs straight along the length of the arm.

Fittingandremovingthedustcassette(g.D&F)

Warning! Always remove the dust cassette and t the

deector when using the tool on metal workpieces.

u Fit the dust cassette (10) over the dust extraction outlet.

u Slide the item onto the tool and make sure that it is

securely located.

u To remove the dust cassette, pull it to the rear and off the

outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KA902E T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KA902E T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info