Bedienungsanleitung Black Decker kc 9024 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

381261

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Charging the battery (fig. C)

The battery needs to be charged before first use

and whenever it fails to produce sufficient power

on jobs that were easily done before.

When charging the battery for the first time,

or after prolonged storage, it will only accept an

80% charge. After several charge and discharge

cycles, the battery will attain full capacity.

The battery may become warm while charging;

this is normal and does not indicate a problem.

Do not charge the battery at ambient

temperatures below 4 °C or above 40 °C.

Recommended charging temperature:

approx. 24 °C.

◆ To charge the battery, insert the charger plug

(7) into the connector (3).

◆ Plug in the charger. Switch on at the mains.

◆ Leave the tool connected to the charger for at

least 12 hours.

The tool can be left connected to the charger

indefinitely. The charger may hum and become

warm while charging; this is normal and does not

indicate a problem.

◆ Before using the tool, unplug the charger and

disconnect the tool from the charger.

Do not use the tool while it is connected

to the charger.

Operating the tool (fig. D)

◆ To tighten a screw or nut, slide the on/off

switch (1) to the right and press it.

◆ To loosen a screw or nut, slide the on/off

switch (1) to the left and press it.

◆ To switch the tool off, release the on/off switch.

Hints for optimum use

◆ Always use the correct type and size of

screwdriver bit.

◆ If screws are difficult to tighten, try applying a

small amount of washing liquid or soap as a

lubricant.

◆ Use the spindle lock to loosen very tight

screws or to firmly tighten screws.

◆ Always hold the tool and screwdriver bit in a

straight line with the screw.

◆ When screwing in wood, it is recommended to

drill a pilot hole with a depth equal to the

length of the screw. A pilot hole guides the

screw and prevents splintering or distortion of

the wood. For the optimum size of the pilot

hole, refer to the table below.

◆ When screwing in hardwood, also drill a

clearance hole with a depth equal to half the

length of the screw. For the optimum size of

the clearance hole, refer to the table below.

Screw size No. 6 No. 8 No. 10

(3.5 mm) (4 mm) (6 mm)

Pilot hole ø

(softwood) 2 mm 3.2 mm 3.5 mm

Pilot hole ø

(hardwood) 2.5 mm 3.5 mm 4.0 mm

Clearance hole 4 mm 5.0 mm 5.7 mm

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Your charger does not require any maintenance

apart from regular cleaning.

Unplug the charger before cleaning it.

◆ Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

◆ Regularly clean the motor housing using a

damp cloth. Do not use any abrasive or

solvent-based cleaner.

PROTECTING THE ENVIRONMENT

Tools

Should you find one day that your tool

needs replacement, or if it is of no further

use to you, think of the protection of the

environment. Black & Decker repair agents

will accept old Black & Decker tools and

ensure that they are disposed of in an

environmentally safe way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kc 9024 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info