Bedienungsanleitung Black Decker KC 9039 (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78925

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

◆ To charge the battery, set the

tool to the straight position

and insert the charger plug

(10) into the connector (11).

◆ Plug in the charger. Switch on

at the mains.

◆ Leave the tool connected to the

charger for at least 12 hours.

The tool can be left connected to

the charger indefinitely.

The charger may hum and become

warm while charging; this is normal

and does not indicate a problem.

◆ Before using the tool, unplug

the charger and disconnect

the tool from the charger.

Do not use the tool while it

is connected to the charger.

Adjusting the handle (fig. D)

For optimum versatility, the

handle can be set to different

positions.

◆ Press the handle adjustment

button (4).

◆ Swivel the handle into the

desired position.

◆ Release the button.

KC9036 - Manual spindle lock

(fig. E)

The manual spindle lock allows

you to use the tool as a regular

screwdriver. You can give an

extra twist to firmly tighten a

screw or to loosen a very tight

screw.

◆ To activate the spindle lock,

turn the collar (2) to the

symbol. With the spindle lock

activated, the tool cannot be

switched on.

◆ To release the spindle lock,

turn the collar (2) to the

symbol.

KC9039 - Setting the torque

(fig. E)

This tool is fitted with a collar to

set the torque for tightening

screws.

Large screws and hard workpiece

materials require a higher torque

setting than small screws and soft

workpiece materials. The collar

has a wide range of settings to

suit your application.

◆ Turn the collar (2) to the

desired setting. If you do not

yet know the appropriate

setting, proceed as follows:

- Set the collar to the lowest

torque setting.

- Tighten the first screw.

- If the clutch ratchets before

the desired result is achieved,

increase the collar setting and

continue tightening the

screw. Repeat until you reach

the correct setting. Use this

setting for the remaining

screws.

Operating the tool (fig. F)

◆ Make sure that the spindle

lock is released.

◆ To tighten a screw or nut,

slide the on/off switch (1) to

the right and press it.

◆ To loosen a screw or nut,

slide the on/off switch (1) to

the left and press it.

◆ To switch the tool off, release

the on/off switch.

Hints for optimum use

◆ Always use the correct type

and size of screwdriver bit.

◆ If screws are difficult to

tighten, try applying a small

amount of washing liquid or

soap as a lubricant.

◆ Use the spindle lock to loosen

very tight screws or to firmly

tighten screws.

◆ Always hold the tool and

screwdriver bit in a straight

line with the screw.

◆ When screwing in wood, it is

recommended to drill a pilot

hole with a depth equal to

the length of the screw.

KC9036EUR.PM65 25-06-2001, 14:5310

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KC 9039 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info