Bedienungsanleitung Black Decker kc 9682 c (Seite 4 von 58) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

387028

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

ENGLISH

• If charging problems persist, take or send

the tool, energy pack and charger to an

authorised service centre.

• The energy pack should be recharged when it

fails to produce sufficient power on jobs which

were easily done previously. Do not continue to

use under these conditions. Follow the charging

procedure described above. You may also

charge a partially used pack whenever you wish.

1 hour charger only:

• The charger and energy pack can be left

connected indefinitely. The charger will keep the

energy pack fully charged.

Switch and forward/reverse lever

(Figs. C1 - 4)

To turn the drill on, squeeze the trigger switch.

To turn the drill off, release the trigger switch

(Fig. C1).

The forward/reverse lever is a three position

lever located over the trigger switch in the

housing.

• During charging, changing accessories

or storage, move the lever to the “Off”

position in the middle (Fig. C2).

• Slide it to the right to drill holes or

drive screws (Fig. C3).

• To remove screws or back out jammed

drill bits, move the lever fully to the left

(Fig. C4).

Two speed selector (Fig. D)

Your drill has a two speed mechanical gear

selector at the top of the housing. In order to

change the speed setting, allow the chuck to

rotate slowly by pressing gently on the

trigger switch.

To select the low speed setting, slide the

selector switch towards the front end of the

drill. The number 1 will appear on the

selector. This will produce a speed ideal for

screwdriving (Fig. D).

To select the high speed setting, slide the

selector switch towards the back end.

The number 2 will appear on the selector.

This will produce a speed ideal for drilling

and hammer drilling.

Warning! Do not change gear while the unit

is running.

Torque control (except KC8402C)

Your drill/driver is equipped with a torque

control mechanism to enable you to do

repetitive screwdriving.

• When screwing in the first screw,

determine the correct torque setting

which will result in the screw being flush

with the surface of the workpiece.

• By keeping the same torque setting,

all following screws will also be flush with

the workpiece, due to the torque

mechanism which disengages the

power of the motor at the moment the

screw is flush.

• This mechanism prevents damage to

the screwhead and the workpiece

(e.g. screws are not driven in too far).

Combination percussion action and

torque adjustment collar (KC8482C,

KC9682C & KC1282C)

These units are equipped with a combination

percussion action and torque adjustment

collar. To select for percussion action rotate

the collar until the hammer symbol is in line

with the indicator on the top of the drill

housing. To select the correct action for

non-masonry drilling tasks rotate the collar

until the drill bit symbol is in line with the

indicator on the top of the drill housing.

For screwdriving, these units are equipped

with 5 position collars, allowing adjustment

of the torque to suit the size of the screw

and the material involved. Before starting

work, adjust the torque in the following way.

Set the collar in position 1 and begin

screwdriving (low torque). If the machine

clutch ratchets too early, adjust the collar to

increase the torque as required.

Maximum recommended capacities

8.4V 9.6V 12V

Steel 10mm 10mm 10mm

Wood 15mm 20mm 25mm

Masonry (combi only) 10mm 10mm 12mm

Chucks (Figs. F1 - 3)

Keyless chuck

To insert a drill bit or other accessory,

follow the steps listed below:

• Switch the control lever to the

“Off” position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kc 9682 c Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info