Bedienungsanleitung Black Decker KC12 (Seite 6 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

473000

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Charger with charging base (fig. E)

◆ To charge the battery (5), remove it from the tool and

insert it into the charging base (8). The battery will only fit

into the charging base in one way. Do not force. Be sure

that the battery is fully seated in the charging base.

◆ Plug in the charger.

After normal use, a charging time of 3 hours will provide

sufficient power for most applications. However, further

charging for up to 6 hours could significantly increase the use

time, depending on the battery and charging conditions.

◆ Remove the battery from the charger.

Charger without charging base (fig. F)

◆ To charge the battery, make sure that it is fitted on the drill.

◆ Insert the charger plug (10) into the connector (9).

◆ Plug in the charger. Switch on at the mains.

After normal use, a charging time of 3 hours will provide

sufficient power for most applications. However, further

charging for up to 6 hours could significantly increase the use

time, depending on the battery and charging conditions.

◆ Disconnect the tool from the charger.

Warning! Do not use the tool while it is connected to the charger.

Selecting the direction of rotation (fig. A)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

◆ To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the operating mode or torque (fig. G)

This tool is fitted with a collar to select the operating mode

and to set the torque for tightening screws. Large screws and

hard workpiece materials require a higher torque setting than

small screws and soft workpiece materials. The collar has a

wide range of settings to suit your application.

◆ For drilling in wood, metal and plastics, set the collar (3)

to the drilling position by aligning the symbol

with the

marking (15).

◆ For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

◆ Set the collar (3) to the lowest torque setting.

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Switching on and off

Variable speed switch

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ To switch the tool off, release the variable speed switch.

Two-speed on/off switch

◆ To switch the tool on, press the on/off switch (1).

When slightly pressing the switch, the tool will run at low

speed. When pressing the switch further, the tool will run

at high speed.

◆ To switch the tool off, release the variable speed switch.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line with the

drill bit.

◆ Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

◆ Use a block of wood to back up workpieces that may splinter.

◆ Use spade bits when drilling large diameter holes in wood.

◆ Use HSS drill bits when drilling in metal.

◆ Use a lubricant when drilling metals other than cast iron

and brass.

◆ Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning. Your charger does not require any

maintenance apart from regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KC12 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info