Bedienungsanleitung Black Decker KC2000 (Seite 7 von 12) (Englisch)

25066

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Warning! Never use the sanding head without a sanding

sheet or accessory in place.

Replacing the diamond sanding tip (fig. F & J)

Sanding sheets are supplied with two replacement diamond

tips. The diamond tip can be reversed when worn. When both

sides are worn, replace the diamond tip.

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position (fig. F).

◆ To reverse the tip, remove it, turn it 180° and press it back

onto the base as shown (fig. J).

◆ To replace the tip, pull the old tip off the base and press a

new one onto the base.

Warning! When removing the tip from the pad, be careful not

to pull the pad off the sanding base.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. A)

The battery needs to be charged before first use and whenever

it fails to produce sufficient power on jobs that were easily

done before. A new battery, or a battery that has not been

used for an extended period of time, achieves full performance

only after approx. 5 charging and discharging cycles. The battery

may become warm while charging; this is normal and does not

indicate a problem. After normal use, a charging time of

60 minutes will provide sufficient power for most applications.

However, further charging for up to 90 minutes could

significantly increase the use time, depending on the battery

and charging conditions.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging temperature:

approx. 24 °C.

◆ To charge the battery (5), remove it from the tool and

insert it into the charger (12). The battery will only fit into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (13) lights up. If the

green end of charge indicator (14) lights up now instead,

the battery is too hot and cannot be charged.

If this happens, remove the battery from the charger, let

the battery cool down for approx. 1 hour and re-insert it.

After approx. 1 hour of charging, the red charging indicator (13)

will stop lighting and the green end of charge indicator (14)

will light up. The battery is now fully charged.

◆ Remove the battery from the charger.

Selecting the torque or drill position (fig. E)

This tool is fitted with a collar to set the torque for tightening

screws.

u For drilling, set the collar (7) to the drilling position by

aligning the symbol

with the marking (21).

◆ For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

◆ Set the collar (7) to position 1.

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Selecting the direction of rotation (fig. A)

For drilling, sawing, sanding and tightening screws, use forward

(clockwise) rotation. For loosening screws or removing a jammed

drill bit, use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

◆ To lock the tool, set the forward/reverse slider into the

centre position.

Drilling/screwdriving (fig. A)

◆ Select forward or reverse rotation using the forward/

reverse slider (2).

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ To switch the tool off, release the variable speed switch.

Setting the sawing angle (fig. F & H)

The saw shoe can be set to angles of 0° (straight) and 45°

(right-side bevel).

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position (fig. F).

◆ Loosen the screw (19) until the shoe can move freely (fig. H).

◆ Pull the saw shoe forward and tilt it into the required angle.

◆ Tighten the screw (19).

Sawing (fig. F)

◆ Select forward rotation by moving the forward/reverse

slider (2) to the left.

◆ To switch the tool on, keep the lock-off button (9)

depressed and press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ Release the lock-off button (9).

◆ To switch the tool off, release the variable speed switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KC2000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KC2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info