Bedienungsanleitung Black Decker KC7251 (Seite 30 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

472996

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

CHANGING THE CHUCK

Make sure the forward/reverse switch is set to the

centre (lock-off) position.

To remove the chuck,

open the jaws, hold it

firmly in one hand and

with a screwdriver held in

the other hand, turn the

set-screw in the chuck

clockwise approximately

one turn, to loosen it.

Place an allen key in the

chuck and tighten the

jaws. Give the allen key

a short powerful blow in

an anti-clockwise

direction with a hammer

to loosen the chuck on

the spindle. Remove the

allen key. Use the screwdriver to turn the set-screw

clockwise until it totally disengages from the spindle.

Remove the chuck from the spindle by rotating it anti-

clockwise. To fasten the chuck, put it on the thread and

turn it clockwise until it stops. Put in the screw and

turn it anti-clockwise until absolutely firm.

HANDY HINTS

• Clamp the workpiece securely.

• When drilling thin material, use a ‘back up’ block to

prevent damage to the workpiece when the drill

breaks through. Just before the tip breaks through

to the opposite side, decrease the pressure on the

drill; this will give a clean hole.

• Use sharp drill bits only.

• When using your drill as a screwdriver, always use

the correct size and type of screwdriver bit.

• When using your drill as a screwdriver, lubricating

the screws can assist in fitting the screw. The usual

lubricants are either soap or washing liquid. Apply a

little to the screw.

• When drilling wood, use twist drill bits.

• When drilling metal, use high speed twist drill bits.

• When drilling ferrous metals, use a lubricant. Iron

and brass are drilled without a lubricant.

• Make an indentation with a centre punch at the centre

of the required hole. This will improve the accuracy.

• Always apply pressure in a straight line with the

drill bit.

TOOL CARE

Do not put excessive pressure on your drill. Use

sufficient pressure to keep your drill/driver biting, but

do not push hard enough

to stall the motor.

After use, remove the

drill bit, open the chuck

jaws fully and tap the

side of the chuck to

remove any sawdust.

RECHARGEABLE BATTERIES AND THE ENVIRONMENT

Black & Decker cordless tools use nickel

cadmium (NiCad) batteries or battery packs

which can be charged many times to give long

life and repeatedly full power.

This symbol indicates the NiCad batteries

contained within this unit must be disposed of

properly and not discarded in everyday household

waste which may be disposed of in an incinerator

or landfill site. NiCad batteries can be harmful to the

environment and can explode when exposed to fire.

Do not incinerate.

Therefore, when your tool or battery pack needs

replacing, think of the protection of our environment.

Black & Decker recommends the following:

• Discharge batteries completely by running the

unit until the energy is completely discharged

and then remove from the tool.

• Take the battery pack to your local dealer or

your local recycling station. If necessary,

contact your local council for disposal

information. The collected batteries will be

disposed of properly and/or used for recycling

purposes whilst protecting the environment.

Note: You as a customer are responsible for

proper disposal or recycling of the battery pack.

EC DECLARATION OF CONFORMITY

We declare that units: KC1251CN, KC1252CN, KC1451CN,

KC7251CN, KC9651CN, KC9652CN, KC1261CN, KC1461CN,

KC9661CN conform to 89/392/EEC, 89/336/EEC, EN55014,

EN60335, EN55104, EN50144, EN61000

A weighted sound pressure 70dB (A)

A weighted sound power 83dB (A)

Hand/arm weighted vibration <2.5m/s

Colin Wills - Director of Engineering - BDCI,

4/F, 2 Dai Wang Street, Tai Po Ind Est, Tai Po NT, Hong Kong

The Black & Decker policy is one of continuous improve-

ment to our product and as such we reserve the right to

change the product specification without prior notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KC7251 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info