Bedienungsanleitung Black Decker kd 1000 (Seite 23 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

386621

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Set the forward/

reverse switch to the

desired direction of

rotation. Never change

the setting of the

hammer switch, the

speed switch, the

torque speed control

or the forward/reverse

when your drill is in

operation.

USING YOUR DRILL

To switch your

drill on, depress

the on/off switch

or the variable

speed switch.

Your drill stops

when the on/off

switch or the

variable speed

switch is released.

If continuous

operation is

required, depress

the lock-on button

while the on/off

switch or variable

speed switch is

depressed. To stop

your drill when operation is continuous, depress the on/

off switch or variable speed switch again and release.

While your drill is in operation, do not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.

• Set the correct drill speed.

Set the torque speed

control to the correct

setting for the size

of screw and the

material.

• Always hold your drill using the handle and the

side handle.

• Always hold your drill at right-angles to your work.

When drilling

wood and metal,

set the hammer

switch to the drill

mode .

When drilling

masonry, set the

hammer switch

to the hammer

mode .

When screwdriving, set the hammer switch to the drill

mode .

• Set the forward/reverse switch to the correct direction.

• Never change the direction of rotation when your

drill is in operation.

• After use, remove the drill bit and gently tap the side

of the chuck with a soft-faced hammer to remove

the dust. This will extend the life of the chuck.

COOLING DOWN

If your drill becomes too hot in use, set the speed

control to its highest setting and allow your drill to

operate without load for 2 minutes.

OVERLOAD

Never use excessive force when using your drill. Too

much pressure can reduce the speed of your drill and

reduce its efficiency. This can result in an overload

which can cause damage to the motor of your drill.

EC DECLARATION OF CONFORMITY

We declare that units: KD574RE, KD574CRE, KD577RT,

KD577CRT conform to 89/392/EEC, 89/336/EEC, EN55014,

73/23/EEC, EN55104, EN50144

A weighted sound pressure 94dB (A)

A weighted sound power 107dB (A)

Hand/arm weighted vibration 10.85m/s

We declare that unit KD1000 conforms to 89/392/EEC,

89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144

A weighted sound pressure 96dB (A)

A weighted sound power 109dB (A)

Hand/arm weighted vibration 9.4m/s

Brian Cooke - Director of Engineering

Black & Decker Ltd, Spennymoor, County Durham

DL16 6JG United Kingdom

The Black & Decker policy is one of continuous

improvement to our product and as such we reserve

the right to change the product specification without

prior notice.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kd 1000 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info