Bedienungsanleitung Black Decker KG1200 T2 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578571

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Removing

u Use a screwdriver to remove the screws (10).

u Remove the ange (9), guard (6) and spring washer (8).

Store these parts carefully.

Warning! Never use the tool without the guard.

Adjusting the guard

The guard can be rotated 90°.

u Rotate the guard as required.

Fitting the side handle

u Screw the side handle (4) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs

(g.C-E)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size

(see technical data).

Fitting

u Fit the guard as described above.

u Place the inner ange (11) onto the spindle (7) as shown

(g. C). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (12) onto the spindle (7) as shown (g. C).

If the disc has a raised centre (13), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner ange.

u Place the outer ange (14) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. D). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. D).

u Keep the spindle lock (5) depressed and tighten the outer

ange using the two-pin spanner (15) (g. E).

Removing

u Keep the spindle lock (5) depressed and loosen the outer

ange (14) using the two-pin spanner (15) (g. E).

u Remove the outer ange (14) and the disc (12).

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Switching on and off

u To switch the tool on, press the lock-off button (2) and

subsequently press the on/off switch (1).

u For continuous operation, press the lock-on button (3) and

release the on/off switch.

u To switch the tool off, release the on/off switch. To switch

the tool off in continuous operation, press the on/off switch

once more and release it.

Warning! Do not switch the tool off while under load.

Hints for optimum use

u Firmly hold the tool with one hand around the side handle

and the other hand around the main handle.

u When grinding, always maintain an angle of approx. 15°

between the disc and the workpiece surface.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack,

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in you appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior (when tted).

Mainsplugreplacement(U.K.&Irelandonly)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KG1200 T2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info