Bedienungsanleitung Black Decker KG2000 (Seite 8 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

497033

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Wear safety glasses or goggles when operating this

tool.

Wear ear protection when operating this tool.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Lock-off button

3. Side handle

5. Spindle lock

5. Guard

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing the guard (g. A)

The tool is supplied with a guard intended for grinding

purposes only. If the unit is intended to perform cutting off

operations, a guard specic for this operation must be tted. A

suitable guard for cutting off operations part number 1004484-

03 is available and can be obtained from Black & Decker

service centres.

Fitting

u Place the tool on a table, with the spindle (6) facing up.

u Hold the guard (5) over the tool as shown.

u Align the holes in the adjusting plate (7) with the screw

holes (8).

u Press the guard down and insert the screws (9) into the

holes.

u Tighten the screws.

Removing

u Remove the screws (9).

u Remove the guard from the tool.

Warning! Never use the tool without the guard.

Adjusting the guard (g. B)

The guard can be rotated 180°.

u Slacken the screws (9) and the nut (10).

u Rotate the guard as required.

u Re-tighten the screws and the nut.

Fitting the side handle

u Screw the side handle (3) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs (g.

C - F)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size (see

technical data). The maximum thickness for grinding discs is 6

mm, for cutting discs 3.5 mm.

Fitting

u Fit the guard as described above.

u Place the inner ange (11) onto the spindle (6) as shown

(g. C). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (12) onto the spindle (6) as shown (g. D).

If the disc has a raised centre (13), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner

ange.

u Place the outer ange (14) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. E). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. E).

u Keep the spindle lock (4) depressed and tighten the outer

ange using the two-pin spanner (15) (g. F).

Removing

u Keep the spindle lock (4) depressed and loosen the outer

ange (14) using the two-pin spanner (15) (g. F).

u Remove the outer ange (14) and the disc (12).

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KG2000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info