Bedienungsanleitung Black Decker KG915 T3 (Seite 6 von 96) (Deutsch, Englisch, Französisch)

578204

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

c. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions

to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualiﬁ ed

repair person using only identical replace-

ment parts. This will make sure that the safety

of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for

grinding, sanding, wire brushing, polishing

or abrasive cutting-off operations

 This power tool is intended to function as

a grinder, sander, wire brush, polisher or

cut-off tool. Read all safety warnings, in-

structions, illustrations and speciﬁ cations

provided with this power tool. Failure to follow

all instructions listed below may result in electric

shock, ﬁ re and/or serious injury.

 Operations for which the power tool was not

designed may create a hazard and cause

personal injury.

 Do not use accessories which are not spe-

ciﬁ cally designed and recommended by the

tool manufacturer.

Just because the accessory can be attached to

your power tool, it does not assure safe opera-

tion.

 The rated speed of the accessory must be at

least equal to the maximum speed marked

on the power tool. Accessories running faster

than their rated speed can break and ﬂ y apart.

 The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

 The arbour size of wheels, ﬂ anges, backing

pads or any other accessory must properly

ﬁ t the spindle of the power tool. Accessories

with arbour holes that do not match the mounting

hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss

of control.

 Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks, back-

ing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

After inspecting and installing an accessory

and run the power tool at maximum no-load

speed for one minute. Damaged accessories

will normally break apart during this test time.

 Wear personal protective equipment. De-

pending on application, use face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

ﬂ ying debris generated by various operations.

The dust mask or respirator must be capable of

ﬁ ltering particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

 Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken acces-

sory may ﬂ y away and cause injury beyond

immediate area of operation.

 Hold the power tool by insulated gripping

surfaces, because the sanding belt / sand-

ing base may contact its own cord. Cutting

a "live" wire may make exposed metal parts of

the power tool "live" could give the operator an

electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KG915 T3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KG915 T3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info