Bedienungsanleitung Black Decker kr 2000 k (Seite 4 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388538

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

Features

This tool includes some or all of the following features (fig. A)

1. Variable speed switch

2. Lock-on button

3. Bit holder

4. Locking ring

5. Forward/reverse switch

6. Direction of rotation indicator

7. Torque adjustment collar

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting and removing a drill bit or screwdriver bit (fig. B)

Fitting

This tool uses screwdriver bits and drill bits with a 1/4" (6.35 mm)

hexagonal shank.

◆ Insert the bit shaft into the bit holder (3) and press it

down until it clicks in place.

Removing

Warning! The drill bit may be hot just after drilling.

◆ Pull the locking ring (4) backwards and take the bit out of

the bit holder.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation (fig. C)

◆ For drilling and for tightening screws, move the forward/

reverse switch (5) to the right. The direction indicator (6)

shows a forward pointed arrow.

◆ For loosening screws or removing a jammed bit, move the

forward/reverse switch to the left. The direction indicator

shows a backward pointed arrow.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the torque or drill position (fig. D)

This tool is fitted with a collar to set the torque for tightening

screws.

◆ For drilling, turn the collar (7) to the left until the symbol

aligns with the marking (8).

◆ For screwdriving, set the collar to the desired setting. If you

do not yet know the desired setting, proceed as follows:

◆ Turn the collar (7) completely to the right (lowest torque).

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired result is

achieved, increase the torque by turning the collar to

the left. Continue tightening the screw. Repeat until

you reach the correct setting. Use this setting for the

remaining screws.

Switching on and off (fig. A)

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

As a general rule, use low speeds for large diameter drill

bits and high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line with the

drill bit.

◆ Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

◆ Use a block of wood to back up workpieces that may splinter.

◆ Use spade bits when drilling large diameter holes in wood.

◆ Use masonry drill bits when drilling into light masonry.

◆ Use HSS drill bits when drilling in metal.

◆ Use a lubricant when drilling metals other than cast iron

and brass.

◆ Make an indentation with a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small amount

of washing liquid or soap to the thread as a lubricant.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

◆ When screwing in wood, it is recommended to drill a pilot

hole with a depth equal to the length of the screw.

◆ A pilot hole guides the screw and prevents splintering or

distortion of the wood. For the optimum size of the pilot

hole, refer to the table below.

◆ When screwing in hardwood, also drill a clearance hole with

a depth equal to half the length of the screw. For the

optimum size of the clearance hole, refer to the table below.

Screw size Pilot hole ø (softwood)

No. 6 (3.5 mm) 2 mm

No. 8 (4 mm) 3.2 mm

No. 10 (5 mm) 3.5 mm

Screw size Pilot hole ø (hardwood)

No. 6 (3.5 mm) 2.5 mm

No. 8 (4 mm) 3.5 mm

No. 10 (5 mm) 4.0 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kr 2000 k Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info