Bedienungsanleitung Black Decker KR 50 CREK (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78815

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for impact drills

◆ Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

◆ Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Side handle

6. Chuck

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (fig. A)

◆ Turn the grip (7) counterclockwise until you can slide the

side handle (5) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit (fig. B)

◆ Open the chuck by turning the front part (8) with one hand

while holding the rear part (9) with the other.

◆ Insert the bit shaft (10) into the chuck and firmly tighten

the chuck.

Removing and refitting the chuck (fig. C)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw (11), located in the front

part of the chuck, by turning it clockwise using a screwdriver.

◆ Tighten an Allen key (12) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation (fig. D)

◆ For drilling and for tightening screws, place the forward/

reverse switch (3) in the neutral position.

◆ For loosening screws or removing a jammed drill bit, turn

the forward/reverse switch (3) to the left.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (4) to

the

position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (4) to the

position.

Switching on and off (fig. E)

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

As a general rule, use low speeds for large diameter drill

bits and high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool.

By using these accessories you will get the very best from

your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR 50 CREK Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info