Bedienungsanleitung Black Decker kr 580 (Seite 25 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

386985

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

depth stop and the end of the drill bit is equal to the

length of the screw you will fit. Tighten the side handle.

PREPARING YOUR DRILL FOR OPERATION

Proceed as follows:

Fit the correct accessory for the job.

Set the speed of

your drill by

setting the

variable speed

control to the

desired position.

As a general rule,

for large size drill bits use low speeds and for smaller

drill bits use high speeds.

Set the forward/

reverse switch to

the desired

direction of

rotation. Never

change the setting

of the hammer/

drill switch, the variable speed control or the forward/

reverse switch when your drill is in operation.

USING YOUR DRILL

To switch your

drill on, depress

the on/off switch.

Your drill stops

when the switch

is released.

If continuous

operation is

required, depress

the lock-on button

while the on/off

switch is

depressed. To stop

your drill when

operation is

continuous, depress the switch again and release.

While your drill is in operation, do not touch the chuck.

HANDY HINTS

• Fit the correct size and type of drill or screwdriver bit.

• Always hold your drill using the handle and the

side handle.

• Always hold your drill at right-angles to your work.

When drilling

wood and metal,

set the hammer/

drill switch to the

drill mode .

When drilling

masonry, set the

hammer/drill

switch to the

hammer mode . When screwdriving, set the

hammer/drill switch to the drill mode .

• Set the forward/reverse switch to the correct direction.

• Never change the direction of rotation when your

drill is in operation.

• After use, remove the drill bit and gently tap the side

of the chuck with a soft-faced hammer to remove

the dust. This will extend the life of the chuck.

COOLING DOWN

If your drill becomes too hot in use, set the variable

speed control to its highest setting and allow your drill

to operate without load for 2 minutes.

OVERLOAD

Never use excessive force when using your drill. Too

much pressure can reduce the speed of your drill and

reduce its efficiency. This can result in an overload

which can cause damage to the motor of your drill.

EC DECLARATION OF CONFORMITY

We declare that units: KR580RE, KR580CRE, KR650RE,

KR650CRE, KR700RE, KR700CRE conform to 98/37/EC,

89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144

A weighted sound pressure 99dB (A)

A weighted sound power 112dB (A)

Hand/arm weighted vibration 8.89m/s

Brian Cooke - Director of Engineering

Black & Decker Ltd, Spennymoor, County Durham

DL16 6JG United Kingdom

The Black & Decker policy is one of continuous

improvement to our product and as such we reserve

the right to change the product specification without

prior notice.

ENGLISH

KR580-700 ML p21-35 05-02-2001, 10:4825

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kr 580 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info