Bedienungsanleitung Black Decker KR500 T2 (Seite 8 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

601801

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

ASSEMBLY

Before attempting any of the following

operations, make sure that the tool is

switched off and unplugged.

Fitting the side handle (fig. B)

◆ Turn the grip (9) counterclockwise until you can

slide the side handle (5) onto the front of the

tool as shown.

◆ Rotate the side handle into the desired position.

◆ Tighten the side handle by turning the grip

clockwise.

Fitting a drill bit or screwdriver bit

Keyless chuck (fig. C)

◆ Open the chuck by turning the front part (10)

with one hand while holding the rear part (11)

with the other.

◆ Insert the bit shaft (12) into the chuck and

firmly tighten the chuck.

Keyed chuck (fig. D)

◆ Open the chuck by turning the sleeve (13).

◆ Insert the bit shaft (12) into the chuck.

◆ Insert the chuck key (14) into each hole (15) in

the side of the chuck and turn until tight.

Removing and refitting the chuck (fig. E)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw by turning it

clockwise using a screwdriver.

◆ Tighten an Allen key (16) into the chuck and

strike it with a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle

and secure it with the chuck retaining screw.

USE

◆ Let the tool work at its own pace.

Do not overload.

◆ Before drilling into walls, floors or

ceilings, check for the location of wiring

and pipes.

Selecting the direction of rotation (fig. A)

◆ For drilling and for tightening screws, slide the

forward/reverse switch (7) forward.

◆ For loosening screws or removing a jammed

drill bit, slide the forward/reverse switch (7)

backward.

Never change the direction of rotation

while the motor is running.

Selecting the drilling mode (fig. A)

◆ For drilling in masonry, set the drilling mode

selector (4) to the position.

◆ For drilling in other materials and for

screwdriving, set the drilling mode selector (4)

to the position.

Switching on and off (fig. A)

Variable speed switch

◆ To switch the tool on, press the variable speed

switch (1). The tool speed depends on how far

you press the switch. As a general rule, use low

speeds for large diameter drill bits and high

speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on

button (2) and release the variable speed switch.

This option is available only at full speed.

◆ To switch the tool off, release the variable

speed switch. To switch the tool off when in

continuous operation, press the variable speed

switch once more and release it.

On/off switch

◆ To switch the tool on, press the on/off switch (1).

If the tool has a two-speed selector (3), set it to

the required speed range. As a general rule,

use low speeds for large diameter drill bits and

high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on

button (2) and release the on/off switch.

◆ To switch the tool off, release the on/off

switch. To switch the tool off when in

continuous operation, press the on/off switch

once more and release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR500 T2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info