Bedienungsanleitung Black Decker KR550CRE T4 (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

601819

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Side handle

4. Depth stop

5. Chuck

6. Drilling mode selector

7. Forward/reverse switch

8. Variable speed control knob

9. Spindle lock button

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

◆ Turn the grip (10) counterclockwise until you can slide the

side handle (3) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Insert the depth stop (4) into the mounting hole as shown.

◆ Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of

the drill bit and the front end of the depth stop.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit

Keyless chuck with spindle lock (fig. B)

◆ Keep the spindle lock button (9) depressed and open the

chuck.

◆ Insert the bit shaft (11) into the chuck and firmly tighten

the chuck.

Keyless chuck (fig. C)

◆ Open the chuck by turning the front part (12) with one

hand while holding the rear part (13) with the other.

◆ Insert the bit shaft (11) into the chuck and firmly tighten

the chuck.

Keyed chuck (fig. D)

◆ Open the chuck by turning the sleeve (14).

◆ Insert the bit shaft (11) into the chuck.

◆ Insert the chuck key (15) into each hole (16) in the side of

the chuck and turn until tight.

Removing and refitting the chuck (fig. E)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw by turning it clockwise

using a screwdriver.

◆ Tighten an Allen key (17) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation

◆ For drilling and for tightening screws, slide the forward/

reverse switch (7) forward.

◆ For loosening screws or removing a jammed drill bit, slide

the forward/reverse switch (7) backward.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (6) to

the position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (6) to the position.

Switching on and off

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

If the tool has a variable speed control knob (8), set it to

the required speed range. As a general rule, use low

speeds for large diameter drill bits and high speeds for

smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to high

quality standards and designed to enhance the performance of

your tool. By using these accessories you will get the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Protecting the environment

Black & Decker provides a facility for recycling

Black & Decker products once they have reached the

end of their working life.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR550CRE T4 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info