Bedienungsanleitung Black Decker KR654CRES T2 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

601836

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Features

1. Variable speed switch

2. Lock-on button

3. Forward/reverse button

4. Drilling mode selector

5. Chuck

6. Depth stop (

not all models)

7. Side handle (not all models)

fig. B

8. Manual spindle lock button (single sleeve keyless

chuck only)

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

X Turn the grip counter clockwise until you can slide the

side handle (7) onto the front of the tool as shown.

X Rotate the side handle into the desired position.

X Insert the depth stop (6) into the mounting hole as

shown.

X Set the drilling depth as described below.

X Tighten the side handle by turning the grip clockwise.

Fitting a drill bit

Single sleeve keyless chuck (fig. B)

X Open the chuck by pressing the manual spindle lock

button (8) and turning the sleeve (9) counter clockwise.

X Insert the bit shaft (12) into the chuck.

X Firmly tighten the chuck by pressing the manual spindle

lock button (8) and turning the sleeve clockwise until

it is tight.

Two sleeve keyless chuck (fig. C)

X Open the chuck by turning the front part (10) with one

hand while holding the rear part (11) with the other.

X Insert the bit shaft (12) into the chuck and firmly

tighten the chuck.

Keyed chuck (fig. D)

X Open the chuck by turning the sleeve (11) counter

clockwise.

X Insert the bit shaft (12) into the chuck.

X Insert the chuck key (14) into each hole (15) in the side

of the chuck and turn clockwise until tight.

Removing and refitting the chuck (fig. E)

X Open the chuck as far as possible.

X Remove the chuck retaining screw, located in the

chuck, by turning it clockwise using a screwdriver.

X Tighten an Allen key into the chuck and strike it with

a hammer as shown.

X Remove the Allen key.

X Remove the chuck by turning it counter clockwise.

X To refit the chuck, screw it onto the spindle and secure

it with the chuck retaining screw.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, floors or ceilings, check

for the location of wiring and pipes.

Selecting the direction of rotation (fig. F)

For drilling and for tightening screws, use forward

(clockwise) rotation. For loosening screws or removing a

jammed drill bit, use reverse (counter clockwise) rotation.

X To select forward rotation, push the forward/reverse

button (3) to the left position.

X To select reverse rotation, push the forward/reverse

button to the right.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

X For drilling in masonry, set the drilling mode selector (4)

to the position.

X For drilling in other materials and for screwdriving,

set the drilling mode selector to the position.

Setting the drilling depth (fig. G)

X Slacken the side handle (7) by turning the grip counter

clockwise.

X Set the depth stop (6) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

X Tighten the side handle by turning the grip clockwise.

Switching on and off

X To switch the tool on, press the variable speed

switch (1). The tool speed depends on how far you

press the switch. As a general rule, use low speeds

for large diameter drill bits and high speeds for smaller

diameter drill bits.

X For continuous operation, press the lock-on button (2)

and release the variable speed switch. This option is

available only at full speed in both forward and reverse

modes.

X To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation,

press the variable speed switch again and release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR654CRES T2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info