Bedienungsanleitung Black Decker KR70 (Seite 4 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

461868

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for impact drills

◆ Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse slider

4. Levelok

™

straight drilling indicator

5. Drilling mode selector

6. Keyless chuck (KR60(L)/KR70(L))

Quick Connect

™

chuck (KR60QC/KR70QC)

7. Depth stop

8. Side handle

9. Bit storage

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

◆ Turn the grip (10) counterclockwise until you can slide the

side handle (8) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Insert the depth stop (7) into the mounting hole as shown.

◆ Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of

the drill bit and the front end of the depth stop.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit

KR60(L)/KR70(L) - Keyless chuck (fig. B)

◆ Open the chuck by turning the front part (12) with one

hand while holding the rear part (11) with the other.

◆ Insert the bit shaft (13) into the chuck and firmly tighten

the chuck.

KR60QC/KR70QC - Quick Connect

™

chuck (fig. B & C)

The chuck on these models can be easily removed and refitted.

When your project entails both drilling and screwdriving,

fit a screwdriver bit in the spindle and a drill bit in the chuck:

you will then only need to remove the chuck for screwdriving

and refit it for drilling. The screwdriver bit can be left in the

spindle while drilling. You can also fit drill bits with a

hexagonal shaft in this way.

◆ To fit a drill bit, proceed as described above.

◆ To fit a screwdriver bit, proceed as follows:

◆ Remove the chuck (6).

◆ Install a screwdriver bit (16) by pushing it into the spindle

(15) as shown.

◆ To remove the screwdriver bit, pull the ring (17) back and

pull the screwdriver bit out of the spindle.

Removing and refitting the chuck

KR60(L)/KR70(L) - Keyless chuck (fig. D)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw, located in the front

part of the chuck, by turning it clockwise using a

screwdriver.

◆ Tighten an Allen key (18) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

KR60QC/KR70QC - Quick Connect

™

chuck (fig. C)

◆ To remove the chuck (6), keep the release tabs (14)

depressed and pull the chuck off the spindle (15).

◆ To refit the chuck, push it onto the spindle until it is firmly

locked into place.

Warning! Always make sure that the chuck is securely fitted.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR70 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info