Bedienungsanleitung Black Decker KR700CRE T4 (Seite 24 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

601822

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

• The forward/reverse switch controls the direction of

rotation when your drill is used as a screwdriver, or

when clearing a jammed drill bit.

• The adjustable depth stop gives precise control of

the hole depth, when you drill blind holes.

FITTING THE DRILL BIT (KEYLESS CHUCKS)

Proceed as follows:

Disconnect the plug from the electricity supply.

While pressing

the spindle lock,

rotate the chuck

until the jaws are

sufficiently open.

Insert the drill bit

in the jaws of the

chuck and

tighten. Twist the

chuck firmly to securely grip the drill bit.

FITTING THE DRILL BIT (KEYED CHUCKS)

Proceed as follows:

Disconnect the plug from the electricity supply.

Rotate the barrel

of the chuck until

the jaws are

sufficiently open.

Insert the drill bit

in the jaws of the

chuck. Insert the

chuck key with

the end of the

chuck key in one of the three holes in the body of the

chuck, ensuring the head of the chuck key is engaged

with the barrel of the chuck. Turn the chuck key

clockwise to tighten the jaws and securely grip the drill

bit. Remove the chuck key.

REMOVING THE CHUCK (KEYLESS CHUCKS)

Proceed as follows:

To remove the chuck, open the jaws, hold it firmly in

one hand and with a screwdriver held in the other hand,

turn the set-screw in the chuck clockwise

approximately one turn, to loosen it.

Place an allen

key in the chuck

and tighten the

jaws. Give the

allen key a short

powerful blow in

an anti-clockwise

direction with a

hammer to loosen the chuck on the spindle. Remove

the allen key. Use the screwdriver to turn the set-

screw clockwise until it totally disengages from the

spindle. Remove the chuck from the spindle by rotating

it anti-clockwise. To fasten the chuck, put it on the

thread and turn it clockwise until it stops. Put in the

screw and turn it anti-clockwise until absolutely firm.

REMOVING THE CHUCK (KEYED CHUCKS)

To remove the

chuck, open the

jaws of the chuck

with the chuck

key. Hold the

chuck firmly in one

hand, and with a

screwdriver turn

the set screw in

the chuck clockwise with the other hand until it comes

out. Use only the correct chuck key. Place the chuck

key into the chuck, and hold the drill firmly in one hand

with the chuck pointing away from you. Rotate the

chuck so that the chuck key is just above the horizontal

position on the right hand side of the machine. Give the

crossbar end of the key a sharp downward blow with a

mallet or light hammer. The chuck should now be

sufficiently loose to be unscrewed by hand.

FITTING THE SIDE HANDLE

Loosely locate

the handle on the

body of your drill.

Rotate the handle

around the body

of your drill until it

is in the desired

position. Tighten

the handle by

turning clockwise.

SETTING THE ADJUSTABLE DEPTH STOP

Proceed as follows:

Fit the drill bit. Loosen the side handle.

Slide the depth

stop until the end

of the depth stop

aligns with the

end of the drill bit.

Slide the depth

stop until the

distance between

the end of the

ENGLISH

KR580-700 ML p21-35 05-02-2001, 10:4824

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR700CRE T4 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info